Calculate parasitic capacitances

Assignment Help Other Engineering
Reference no: EM131210151

Problem - Consider the CMOS Inverter shown in page 3 supplied with a bias of VDD = 5 V. The technology file for this CMOS is provided in Page 4. Only key design parameters are shown in CMOS mask layout. Grid size shown is 1 µm.

a) TABULATE the areas and perimeters of gate, source, and drain for both nMOS and pMOS transistors (with correct unit).

b) Calculate parasitic capacitances (Cgd, Cgs, Cdb, Cbs) for transistors at zero bias. For Cdb and Cds consider only the junction and sidewall effects. TABULATE your results for both pMOS and nMOS.

c) Calculate VTC inverter parameters: VOH, VOL, VIL, VIH. TABULATE results.

d) Use OrCAD/PSPICE to simulate and examine results in part (c). TABULATE results.

e) For part (d) show CMOS current level at VOH, VOL, VIL, and VIH. OrCAD  only. TABULATE results.

f) Construct a load capacitance (CL) for CMOS circuit assuming that:

CL = 10XΣ2 transistors (Cgd + Cbd + Cbs + Cgs).

g) Use OrCAD/PSPICE to simulate and obtain CMOS's response time: rise-time and fall-time. TABULATE results.

h) For part (d), (e), (f), and (g) MUST SUBMIT OrCAD's

1) Schematics,

2) CMOS parameters used,

3) simulated probe results.

Attachment:- IC Design Assignment.rar

Reference no: EM131210151

Questions Cloud

Define the sublist predicate in a direct fashion : Write in PROLOG a program that computes the length (understood as the number of elements) of a list and returns this value in numeric form. (Hint: consider an inductive definition of length and use the is operator to increment the value in the ind..
Experiencing a net capital inflow or a net capital outflow : If interest rates in the United States were lower than rates in the rest of the world, would the United States be more likely to be experiencing a net capital inflow or a net capital outflow?
Relevance of using macroeconomic and microeconomic data : Explain the top down and bottom up relevance of using macroeconomic and microeconomic data. Is one method superior or should both be used? Support your thought
Differences between a logic program and a prolog program : List the principle differences between a logic program and a PROLOG program. If in a logic program, the order of the atoms in the body of a clause is changed, is the semantics of the program altered? Justify your answer.
Calculate parasitic capacitances : Calculate parasitic capacitances (Cgd, Cgs, Cdb, Cbs) for transistors at zero bias. For Cdb and Cds consider only the junction and sidewall effects. TABULATE your results for both pMOS and nMOS
Approached by a client for help on financial strategy : You are an investment advisor who has been approached by a client for help on his financial strategy. He has $250,000 in savings in the bank. He is fifty five years old, and expects to work for ten more years, making $100,000 a year. (He expects t..
What you think are the major characteristics of a project : What you think are the major characteristics of a project?
What is software project management : How do you define the word, "project"? How are software projects different from other kinds of projects? Why do software development projects fail? What remedial measures can be taken so that software development projects do not fail? What is soft..
What are typical project management processes : What are the essential qualities of a software project manager? What are software project management metrics? How are project management and software development processes related to each other?

Reviews

Write a Review

Other Engineering Questions & Answers

  Use the ansi recommendations for keyway design

1) he rotating 1050 cold rolled steel shaft shown in the figure below is simply supported at the center of two bearings (denoted by an X) and the only applied load is the constant 7kN load. All dimensions are in mm and all steps in the shaft have ..

  Can be cooled down by running through ferromagnetic material

Superconducting magnets are used to generate massive magnetic fields that cause large magnetizations in the ferromagnetic inductor. Below are three candidate materials for the superconducting magnet. Based on what you know about superconductors, w..

  Demonstrate and identify your productions or supply

Demonstrate and identify your productions or supply and provide the components, the client/buyer ask you to prepare a technical report involving all technical aspects to illustrate the capabilities and usage.

  Draw a functional block diagram for the system

Which may be represented as disturbances acting between the pulley and stick subsystems. Draw a functional block diagram for the above system, showing its major components as well as all signals.

  Compare the meter reading with the oscilloscope reading

Compare the meter reading with the oscilloscope reading. Use the digital voltmeter to measure the AC voltage of the sine wave. Enter this value in Table I. Repeat steps 3.4 and 5 for the square wave and the trianeular wave.

  Draw the free-body diagram

Draw the free-body diagram of the 50-kg paper roll which has a center of mass at G and rests on the smooth blade of the paper hauler. Explain the significance of each force acting on the diagram. (SeeFigure)

  Calculate the thrust on the valve and the depth

Calculate the optimum diameter of the input piston which will allow the press to operate and determine the centre of pressure on immersed surfaces

  Develop your own timing diagram for a memory read

Develop your own timing diagram for a memory read that is analogous to the write diagram for picture below. You can use whatever control lines you want.

  Can a local maximum be a global minimum

Can a local maximum be a global minimum - Can a local minimum be greater than a local maximum? Yes or No? Explain your answer.

  Provide a detailed management plan for this operation

MRE80002 Dredging Engineering 2016 Assignment. Your task is to provide a detailed management plan for this operation. The plan should include, but not necessarily be limited to, Project background & Objectives, Project safety, Environmental issues ..

  Research paper on the topic - reservoir characterisation

Give preferences that will provides students with a detailed understanding of the rock and rock-fluid properties of oil and gas reservoirs; an understanding of the Darcy equation

  Determine the work done by the butane during the process

Show that it is reasonable to assume that butane behaves as an ideal gas during this process. Determine the work done by the butane during the process.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd