Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
1. Calculate the length of time it takes for a signal to pass down an Ethernet bus that is 300 m in length, assuming the velocity factor of the cable is 0.66.
2. For the Ethernet bus in problem 1 and a communication rate of 10 Mb/s, calculate the total number of bits that would be sent by each station before it detected a collision if:
a) both stations begin to transmit at the same time
b) one station begins to transmit at the first possible moment such that its transmission would not be detected by the other station before it began its transmission
3. Discuss the advantages and disadvantages of shorter and longer packets for different link error rates and different types of data.
4. How many addresses are available in IP version 6? Express this as a decimal number in power-of-ten notation.
Memory storage and bit density, A hard disk contains four Platters. Each side of the platter is coated with a magnetic oxide, allowing data to be stored on it. The platters are 3.5 inches in diameter.
An assembly line can produce 90 units per hr. The line hrly cost is $4500 on stright line ( the first 8 hrs). Workers are guaranteed a minimum of 6 hrs. There is a 50% premiun for overtime (time and a half), how ever productivity drops by 5%.
what is the range of sampling frequencies you can use such that you don't violate Nyquist theorem and still meet or exceed the needed resolution when you perform the FFT operation on the full set of collected data
Semiconductor A has a bandgap of 2.5eV while semiconductor B has a bandgap of 1.5eV. What is the ratio of the intrinsic carrier concentrations in the two materials (niA/niB) at 300K
Design a state graph and state table for a Moore sequential circuit that has two inputs (X1 and X2) and one output (Z). The output begins at 0 and becomes 1 when X1 = 1 and X2 = 1, either concurrently or one after the other
A rectangular chip has a top surface of 0.5 cm by 2 cm cooled by air at 20 oC with h = 150 W/m2.K. There are also 16 connector pins, 1 mm wide, 0.5 mm thick, 6 mm long and k = 60 W/m.K attached to a circuit board at 30 oC.
Determine the transfer function of a second order Butterworth Lowpass filter with a 3dB cutoff of 5 Kilo Hertz. Design a circuit which realizes this filter using Sallen-Key configuration. Find all the values of the circuit elements and determine t..
A 3-phase transmission line series load of 2000MVA, .8 p.f. lag at 735 kv. The ABCD parameters of the line are : A = .8746 =D, B = j128.33Ω, C = j.0018315 (s). Calculate Vs, Is, voltage regulation and efficiency of the line.
Assuming the bandgap of GaAs, Eg1 = 1.424 eV and that of AiAs, Eg2 = 2.671 eV, find the required AI - fraction x in AIxGa1As compound to fabricate the material for red light emission with the wavelength lambda = 652 nm.
A particular diode was measured to have VD = 0.62 V at ID = 5.895 mA. Determine the following: a) the reverse saturation current IS. b) VD for a forward current of 100 mA. Assume VT = 25 mV.
A 3 phase 50hz star connected motor has rotor resistance and stand still reactance of 0.025ohm and 0.35 ohm respectively. The full load slip is 5% calculate the resistance per phase of a star connected rheostat
a) Using a table of the Gaussian distribution, determine an exact value for P[|X-n|>=2.5sigma] b) What is the upper bound on P[|X-n|>=2.5signma] given by the Chebyshev inequality
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd