Calculate how many pounds of strawberries are needed

Assignment Help Mechanical Engineering
Reference no: EM13217518

Strawberries contain about 15 wt% solids and 85 wt% water.

To make strawberry jam, crushed strawberries and sugar are mixed in a 45:55 mass ratio, and the mixture is heated to evaporate water until the residue contains one-third water by mass. Calculate how many pounds of strawberries are needed to make a pound of jam?

 

Reference no: EM13217518

Questions Cloud

What is the output variable : A process with Gp= 2/(2s+1) and Gd=1/(2s+1) experiences a disturbance step change of magnitude 5. The SP remains constant. If a P-controller alone with Kc=1 is used and Ga=Gs=1, then what is the output variable, delta Y(t) versus time?
What is the first order angular separations : The hydrogen spectrum has a red line at 656 nm and a blue line at 434 nm. What is the first order angular separations between these two spectral lines obtained with a diffraction grating that has 4500 lines per centimeter?
Explain how would you respond to coleman''s request : How would you respond to Coleman's request? Be sure to cite research that supports your position. What if you have already told the other side that the building is fine when you learn about the problems?
Correlation coefficient : What would happen to the size and the sign of the correlation coefficient if we correlated these two variables? How can researchers work around this issue?
Calculate how many pounds of strawberries are needed : To make strawberry jam, crushed strawberries and sugar are mixed in a 45:55 mass ratio, and the mixture is heated to evaporate water until the residue contains one-third water by mass. Calculate how many pounds of strawberries are needed to make a..
Evaluate the net present value - npv of the lease : Genmed Hospital needs to replace its existing MRI scanning machine. The hospital is considering funding the purchase by means of a lease. The lease would run initially for 2 years at a cost of R450 000 per annum, payable at the of the year.
State whether each member is in tension or compression : Determine the force in each of the members connecting joints A through F of the vaulted roof truss shown. State whether each member is in tension or compression.
Police situations-corrections facility-juvenile facility : describing how verbal and nonverbal communication can affect communication. Police situations (public announcement to the press) Courtroom setting (testifying) Corrections facility (employees, peers, inmates)
Compute the cost of operating an airline : How has the changing environment in the airline industry affected the cost of operating an airline? Who are the major stakeholders concerned with safety inside and outside of an airline company?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the efficiency of the turbine-generator

A small hydroelectric power plant produces electrical power at a rate of 30 kW. The plant utilizes a stream of water that drops 40 m from a lake to the turbine and flows at a rate of 100 kg/s. What is the efficiency of the turbine-generator?

  Determine the compression ratio

determine (a) the compression ratio, (b) the cycle efficiency, (c) exhaust temperature, and (d) mean effective pressure (kPa). Draw (e) a P-v diagram and (f) a T-s diagram

  Under what conditions is the maximum achieved

A steam turbine is operated ith an input temp of 800C and exhaust temp of 150C. What is the maximum amount of work the turbine can do for a given heat input Q? Under what conditions is the maximum achieved?

  Explain the factor

explain the factor, which inhibit the use of a very high resolution and a large number of colors for display in the case of raster scanning display devices.

  Calculate real gas pseudopressure at a pressure

Calculate real gas pseudopressure at a pressure of 1902.7 psia using the following data and a base pressure of 102.7 psia. Was the calculation of real gas pseudopressure necessary for this gas? Explain your answer.

  Specify a diameter d using a design factor of nd

xerted on the shaft shown in the figure, which rotates at 1150 rev/min and supports a 10-kip bending force. Use a 1095 HR steel. Specify a diameter d using a design factor of nd = 1.6 for a life of 3 min. The surfaces are machined.

  Calculate the mass flow

Calculate the mass flow (in slugs/per second) that comes out the exit of the engine. The plane is at standard altitude 50,000 ft and velocity = 2200 ft/s. Would appreciate attack to problem.

  The gap between them is filled with molten polymer

Two flat, rectangular plates with a lateral dimension w*l lie parallel, one above the other, a distance h apart. The gap between them is filled with molten polymer.

  Which acitivities does hydraulic analysis of a pipeline

which acitivities does hydraulic analysis of a pipeline include using HYSYS software? what data can obtained?

  Estimate the schmid factor

Estimate the Schmid Factor, which is used to convert the CRSS into a critical tensile 'yield' stress. Use the measured angle between the slip trace and the sample long axis

  Determine the magnitude of the boats acceleration

Starting from rest the motorboat travels around the circular path,P = 50m , at a speed v=(0.8t)m/s, where t is in seconds. Determine the magnitude of the boat's velocity when it has traveled 40m. Determine the magnitude of the boat's acceleration ..

  What is the actual mechanical advantage of the system

a first class lever in static equilibrium has a 50lb resistance force and a 15lb effort force. the levers effort force is located 4ft from the fulcrum. what is the actual mechanical advantage of the system?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd