Calculate how far from the fulcrum the tweezer

Assignment Help Mechanical Engineering
Reference no: EM13212920

A medical technician uses a pair of four inch long tweezers to remove a wood sliver from a patient. The technician is applying 1 lb of squeezing force to the tweezers. If more than 1/5 lb of force is applied to the sliver, it will break and become difficult to remove. Using static equilibrium calculations, calculate how far from the fulcrum the tweezers must be held to avoid damaging the sliver.

Reference no: EM13212920

Questions Cloud

How can a firm with such a low profit be worth : To the uninformed observer this does not really make sense. How can a firm with such a low profit be worth so much on the stock market?
Calculate the pressure of methane gas : Calculate the pressure of 15.0g of methane gas in a 1.50L vessel at 45.0 degrees C using (a) the Ideal Gas Law and (b) the van der Walls equation using the following information about the constants, a and b: a = 2.253 and b = 0.04278.
Define economic staff of us department of the treasury : The economic staff of the U.S. Department of the Treasury has been asked to recommend a new tax policy concerning the treatment of the foreign earnings of U.S. firms. Currently the foreign earnings of U.S. multinational companies are taxed only wh..
Evaluate long-term solvency ratio : Calculate the following: Current ratio, long-term solvency ratio, contribution ratio, programs and expense ratio, general and management and expense ratio, fund-raising and expense ratio, and revenue and expense ratio for the years 2003 and 2004.
Calculate how far from the fulcrum the tweezer : Using static equilibrium calculations, calculate how far from the fulcrum the tweezers must be held to avoid damaging the sliver.
Calculate the mass flow : Calculate the mass flow (in slugs/per second) that comes out the exit of the engine. The plane is at standard altitude 50,000 ft and velocity = 2200 ft/s. Would appreciate attack to problem.
What will be the par value of the oid issue : The company's bankers assure Rienegar management that it can raise $3,000,000 by issuing 25-year Original Issue Discount (OID) bonds bearing a 6.25% semiannual coupon.What will be the par value of the OID issue?
Determine the magnitudes of fa and fb : The total force Fa + Fb exerted on the shelter is in the direction parallel to the line L and it's magnitude is 400 lb. Graphically determine the magnitudes of Fa and Fb.
How much in revenues do businesses receive in product market : how much are households paid for providing entrepreneurial ability? $ billion for entrepreneurial ability b. If households spend $80 billion on goods and $70 billion on services, how much in revenues do businesses receive in the product market.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is differential levelling

What is differential levelling? list the procedure for carrying out a differential levelling exercise where one point is beyond the range of the instrement . 100 word limit

  Determine the angular velocity of the rod

Knowing that in the position shown the rod has angular velocity of 4 rad/s clockwise; determine the angular velocity of the rod after it has rotated through a 90°.

  Determine the stress in a stay at a given temperature

Determine the stress in a stay at a given temperature. A steel 'stay' of effective length 5m is fitted in between the walls of a ships refrigerated compartment when the temperature is 18 degrees centigrade.

  Explain the cost of recharging a battery

The Cost of Recharging a Battery, A 12-V automotive storage battery is charged with a constant current of 2 amp for 24 hr.

  A turbine salesman makes the following claim for one

A turbine salesman makes the following claim for one of his products: Steam enters a steady-flow adiabatic turbine at 4 MPa, 600 °C with negligible velocity and exhausts at 200 kPa with a velocity of 180 m/s

  Module fea - finite element analysis

Module FEA - FINITE ELEMENT ANALYSIS ,  Provide answers to all questions. Note that assignment part 2 carries 60% of the marks for the course.

  Calculate the break hp of the pump using water

Using a centrifugal pump, and a flow rate of 60 gal/min, calculate the break hp of the pump using water with a density of 62.4lbm/ft3 and do the same for a nonviscous liquid having a density of 0.85g/cm3.

  Determine the moments of inertia

two 20mm steel plates are welded to a rolled S section as shown. Determine the moments of inertia and the radii of gyration of the combined section with respect to the centroidal x and y axes.

  What is the thrust in kn of this engine

Bypass air exits at 600 m/s while combustion air exits at 1000 m/s. What is the thrust in kN of this engine?

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Calculate the force required in direct extrusion

Calculate the force required in direct extrusion of 1100-O aluminum from a diameter of 6 in. to 2 in. Assume that the redundant work is 30% of the ideal work of deformation, and the friction work is 25% of the total work of deformation.

  Explain working with boiler suspension bolts

Working with boiler suspension bolts. An HRT boiler is 4766mm long and 3533mm in diameter. It has 66 steel tubes with a diameter of 9mm. The total dry weight of the boiler is 2.565 tonnes

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd