Calculate first the temperature at the center of one face

Assignment Help Mechanical Engineering
Reference no: EM13631196

A cube of aluminum 10 cm on each side is initially at a temperature of 300°C and is immersed in a fluid at 100°C. The heat-transfer coefficient is 900 W/ m^2*°C. The transient of a cube is the product of transient of three infinite plates.

Calculate first the temperature at the center of one face after 1 min, then determine the temperature at the center of any of the six faces after one minute.

Reference no: EM13631196

Questions Cloud

Consider a steam power plant that operates on a : consider a steam power plant that operates on a regenerative ranking cycle and has a net power output of 150mw .steam
A compressor is used to bring saturated water vapor at 150 : a compressor is used to bring saturated water vapor at 150 lbfin2 up to 2500 lbfin2 where the actual exit temperature
The turbine exit pressure is 10kpa the overall efficiency : a geothermal power plant is supplied with water at a well bottom temperature of 225 degrees c and a pressure of 8 mpa.
The viscoelastic response of a common orthopedic polymer is : the viscoelastic response of a common orthopedic polymer is represented using a maxwell model so that the spring
Calculate first the temperature at the center of one face : a cube of aluminum 10 cm on each side is initially at a temperature of 300degc and is immersed in a fluid at 100degc.
A he ion is placed in an excited state so that its : a he ion is placed in an excited state so that its remaining electron occupies the n5 state. the electron can make a
A steel thermal diffusivity 000001172 k43 cylinder 10 cm in : a steel thermal diffusivity 0.00001172 k43 cylinder 10 cm in diameter and 10 cm long is initially at 300degc. it is
A steam turbine is operating at a steady state inlet : a steam turbine is operating at a steady state. inlet pressure and temperature are 40 bar and 400 degrees c
A cyclotron is sometimes used for carbon dating carbon-14 : a cyclotron is sometimes used for carbon dating. carbon-14 and carbon-12 ions are obtained from a sample of the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The drain from the closed heater is trapped to the open

steam flow rate kgs for a reheat-regenerative steam power plant which is to produce 200 mw of electricity. the turbine

  Show that this function satisfies the requirements of a

consider the following probability distribution function for a continuous random variablefx 3x6235 -2ltxlt-3

  An automobile tire with a volume of 05m3 is inflated to a

an automobile tire with a volume of 0.5m3 is inflated to a gage pressure of 200 kpa. calculate the mass of air in the

  1 the contraption below has a face cam with an elliptic

1. the contraption below has a face cam with an elliptic pro?le pushing a push rod against a spring. the face cam is

  What is the change of internal energy and enthalpy of 4 kg

what is the change of internal energy and enthalpy of 4 kg nitrogen as it changes from 50oc and 100kpa to 100oc and

  Hot air is contained in a vertical frictionless

hot air is contained in a vertical frictionless piston-cylinder device.the piston has a mass of 4 kg and a

  Determine the total length of the 12 tube that is required

a heater is required to supply the domestic hot water dhw in a 50 unit apartment building where the dhw load is

  Hazen-williams formula -find the diameter of a pipe

Hazen-Williams Formula- Find the Diameter of a Pipe, The length of cast-iron pipe is to be 4200 ft., and the head causing flow is to be 12.6ft. After the pipe has been in service 5 years, it is expected to discharge water at a rate equal to 3.2 cf..

  01 kg of propane is contained within a piston-cylinder

0.1 kg of propane is contained within a piston-cylinder assembly at 0.2 mp initially with a specific internal energy of

  Determine distribution of shear force and bending moment

Determine distribution of shear force and bending moment

  In boulder dam 2000 cubic feet per second of water flows

in boulder dam 2000 cubic feet per second of water flows through each of the pipes called penstocks that lead down to

  Assume that a jet touches down 170 mph and its speed is

assume that a jet touches down 170 mph and its speed is reduced to zero in 240 ft. assuming a constant deceleration

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd