Calculate exit velocity if the velocity at entry

Assignment Help Mechanical Engineering
Reference no: EM13824808

An ideal duct carries water (incompressible fluid) from a height of 10m to 20m. The pressures at the entry and exit points are at 1000 Pa and 2000 Pa respectively. Calculate exit velocity if the velocity at entry is 10 m/s.

 

 

Reference no: EM13824808

Questions Cloud

Rights and liabilities of silent partner : Jason and John are partners in a partnership called Fancy Dress Suppliers' which sells, rents and supplies fancy dress outfits and accessories.
Describe a method to determine the cellular immune response : Describe and discuss a method to determine the cellular immune response to an infectious agent in an individual. Discuss in general how a response to an infectious agent is determined.
The ball is kicked from point a with the initial velocity : The ball is kicked from point A with the initial velocity vA=10m/s. Determine the range R, and the speed when the ball strikes the ground
Quality control for reducing defects in products : Quality Control For Reducing Defects In Products
Calculate exit velocity if the velocity at entry : An ideal duct carries water (incompressible fluid) from a height of 10m to 20m. The pressures at the entry and exit points are at 1000 Pa and 2000 Pa respectively. Calculate exit velocity if the velocity at entry is 10 m/s.
The cylinder to keep the load stationary : A dynamic compression force,F = 3.5 + 3.5cos (45t) kN is applied to the rod of an ideal cylinder with a bore diameter of 8.4 cm (take note that the force is in kN) (a) Assuming the rod-side of the cylinder is at atmospheric pressure, what gauge press..
What is the force ecienccy of the actuator : A cylinder with an area ratio of 0.2 and a bore diameter of 7.5 cm steadily extends a 13.3 kN load. If the cap-side pressure is 4 MPa and the rod-side pressure is 250 kPa, what is the force ecienccy of the actuator?
Discusses about preparing performance report for a project : Prepare a performance report for the Humphrey Catalog project. This problem belongs to Accounting and it discusses about preparing performance report for a project
What signals are involved in the initiation of its functions : What is it? Where is it from? What is its role in the immune system? What signals are involved in the initiation of its functions?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the water content of the material when saturated

The dry desnity of a compacted sand is 1.87 Mg/m^3 and the denisty of the solids is 2.67 Mg/m^3. What is the water content of the material when saturated? Please use phase diagram.

  A flat-plate collector 4m2 in area is tested during the

a flat-plate collector 4m2 in area is tested during the night to measure the overall heat loss coefficient. water at

  At the beginning of the compression process of an

at the beginning of the compression process of an air-standard otto cycle p1 14.7 lbin2 and t1 530degr. the maximum

  The rate of heat flow at the root of the blade

A turbine blade 6.3 cm long with cross-sectional area A 4.6 x 10-4 m2 and perimeter P 0.12 m, is made of stainless steel (k =18 W/m K). The temperature of the root, Ts, is 482°C. The blade is exposed to a hot gas at 871°C and the heat transfer coeffi..

  An ideal gas carnot cycle with air in a piston cylinder

an ideal gas carnot cycle with air in a piston cylinder has a high temperature of 1200 k and a heat rejection at 400 k.

  Provide an example for how microstructure influences

describe the relationship between microstructure scale and material properties. provide an example for how

  The top surface of the oil in the manometer is even with

a closed tank has an enclosed airspace above the surface of water which fills the tank to a depth of something over a

  Consider piston-cylinder-find final volume an temperature

Consider a piston/cylinder with .5kg of R-134a as saturated vapor at -10C. It is now compressed to a pressure of 500kPa in a polytrophic process with n=1.5. Find the final volume an temperature and determine the work done during the process?

  The refrigerator is located in a room that is maintained at

a bottle containing 10 kg of water at an initial temperature of 35 degrees celsius is stored in a refrigerator whose

  Determine the minimum power requirement for the pump

The impeller of a centrifugal pump has inner and outer diameters of 14 and 37cm, respectively, and a flow rate of 0.18m3/s at a rotational speed of 1200rpm. The blade width of the impeller is 8.6cm at the inlet and 3.5cm at the outlet.

  Find the power input to the compressor

A steam compressor receives H   2O at 90kPa and 75% quality at a rate of 50 kg/s. Part way through the compressor, steam is bled off at 20kg/s, 2MPa and 300C. The remainder exits the compressor at 10MPa, 500C. Assuming heat transfer and changes in po..

  Water flows 2m deep at 2ms in a rectangular channel find

water flows 2m deep at 2ms in a rectangular channel. find the change in depth and in water surface elevation caused by

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd