Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
The nameplate on a 50-MVA, 60-Hz single-phase transformer indicates that it has a voltage rating of 8.0-kV: 78-kV. An open-circuit test is conducted from the low-voltage side, and the corresponding instrument readings are 8.0kV, 62.1A, and 206kW. Similarly, a short-circuit test from the low-voltage side gives readings of 674 V, 6.25 kA, and 187 kW.
a. Calculate the equivalent series impedance, resistance, and reactance of the transformer as referred to the low-voltage terminals.
b. Calculate the equivalent series impedance of the transformer as referred to the high-voltage terminals.
c. Making appropriate approximations draw a T equivalent circuit for the transformer.
d. Determine the efficiency and voltage regulation if the transformer is operating at the rated voltage and load (unity power factor).
A U manometer reads 20 cm air as operating fluid and a given manometric fluid. A single branch closed tube reads 35 cm connected to point 1. If P2 = 1.2 ATM calculate the pressure in point 1 and the density of the manometric fluid.
Assume two cables have wire strands that are the same diameter and made of the same material. If one cable has 7 strands and another has 19 strands, which will have more resistance over a mile
A 15hp (output power), 208V, three phase, six pole, y-connected induction motor has the following parameters: R1 = 0.1 ohm R'2= 0.1 ohm Xeq = 0.5 ohm A.) A fan type load is connected to the motor. The slip of the motor in this case is 2%.
Consider the following signal y[n]; y[n] = X1[n+3] * X2[n] The signals X1 and X2 are defined as X1[n]=((1/2)^n) u[n] X2[n]= ((1/3)^n u[n] Determine the Z transform of y[n].
A 190-F capacitance is initially charged to 1190V . At t = 0, it is connected to a 1-k resistance. a) At what time t2 has 50 percent of the initial energy stored in the capacitance been dissipated in the resistance
a dsp system is given with the following specifications: design requirements: sampling rate 20,000 Hz Maximum allowable gain variation from 0 to 4,000 Hz = 2dB 40dB rejection at the frequency of 16000 Hz
We represent this by a non-overlapping sequence detector. In other words, asa soon as you detect the sequence, you will need to get another complete sequence to unlock. Therefore, you need to carefully choose to which state you will need to go.
What is the modulation used to transmit HDTV signals over the air in US terrestrial broadcasting? What is the transmitted bit rate and the compression method?
An 8-bit shift register is used to convert a serial input to a parallel output. If a byte is received every 64 micro-second(us), what is the clock for the register
The circuit will have as inputs a minimum of two inputs; the binary equivalent of two decimal numbers of not greater than (10,000)10. The circuit will also produce a minimum of two outputs, the quotient and the remainder.
It the resistors used are not ideal but have a ±5% manufacturing tolerance, what are the extreme output voltage and resistances that can result?
Analog to Digital Converters The input signals of an (10bits) ADC are from -1Volt to +1Volt. a) What is the rage of the converters b) What is the resolution c) What is the precision What is the value the minimal input signal variation that this ADC c..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd