Calculate equivalent pipe size and flow in the pipe

Assignment Help Civil Engineering
Reference no: EM13308154

Water is transported from a reservoir at higher elevation to another reservoir through a series of three pipes. The first pipe of 400mm diameter is 500 m long, the second pipe 600 m long, size 300mm, and the last pipe is 500m long of diameter 200mm. If the elevation difference between two reservoirs is 30m, calculate equivalent pipe size and flow in the pipe.

Reference no: EM13308154

Questions Cloud

Write a function that convert any angles outside of interval : Suppose that an array contains angles in degrees. Write a function that converts any angles outside of the interval [0,360] to an equivalent angle in that interval. For example, an angle of 380.5 degrees should be converted to 20.5 degrees.
What is the induced emf across the inductor : The current in a 4.70 mH inductor decays over time according to the following function, What is the induced emf across the inductor at t= 5.00 ms
Calculate the braking distance if only the rear brakes work : An automobile traveling at 30 miles per hour on level pavement with a coefficient of kinetic friction of 0.6. Weighs 3,000 lb. Sixty percent of its weight is on the front axle and 40% on the rear axle.
How do you add all the elements of an arraylist : how do you add all the elements of an ArrayList favorite? I need help on creating class and client.
Calculate equivalent pipe size and flow in the pipe : The first pipe of 400mm diameter is 500 m long, the second pipe 600 m long, size 300mm, and the last pipe is 500m long of diameter 200mm. If the elevation difference between two reservoirs is 30m
How are the two directory services alike : Windows Server 2000/2003/2008 uses Active Directory for its directory service, and NetWare / OES uses NOS. How are the two directory services alike? How are they different?
Determine the acceleration a of the plate on the bar : The bar is prevented from rotating by the two pegsA and B fixed to the plate. Determine the acceleration a of the plate for which no force is exerted on the bar by either peg A or B.
Wholesaling and retailing jewellery nationally all across : Pandora Diamonds and Gems Pty Ltd is a company engaged in the business of importing, wholesaling and retailing jewellery nationally all across Australia.
Find the amplitude of current oscillations in the circuit : A 1-microF capacitor, a 10-Ohm resistor and a 1 microH inductor are connected in series with a sinusoidal signal generator of 10V peak voltage amplitude operating at a frequency ω of 100 rad/s. Find the amplitude of current oscillations in the cir..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Formulate and solve the minimum weight design

consider the cantilever beam-mass system. formulate and solve the minimum weight design.

  Estimate the hourly so2 and particle emissions

what type of SO2 removal device before (in front of) or after (following) the particle collector would you use?

  Design a three story office building

Design a three story office building

  Develop the relation between bulk unit weight

develop the relation between bulk unit weight, specific gravity, void ratio and weight of water.

  Find dimension of rectangular concrete channel to carry flow

Find the dimensions of a rectangular concrete channel to carry a flow of 150 m3/s, with bottom slope 0.015, and mean velocity 10.2 m/s.

  Find the work done in pumping the water

a horizontal cylindrical tank 4 ft in diameter and 10 ft long is full of water. find the work done in pumping the water to a point 4 above the top of the tank.

  Determine maximum wind load that cavity wall is used

determine the maximum wind load that the cavity wall , bothe wythes are fully grouted but unreinforced ,and type S mortar portland cement is used . prism strength is equal to 2666psi for the concrete block wythe and 5333 psi for the brick wythe.

  Determine the friction drag on one side of the plate

Water flows past a triangular flat plate oriented parallel to the free stream as shown. Integrate the wall shear stress over the plate to determine the friction drag on one side of the plate. Assume laminar boundary layer flow.

  Determine the normal depth-critical depth and velocity

A PVC pipe with a diameter of 30 inches will carry a flow of 20 cfs. the bottom slope is 0.005 and the roughness coefficient is 0.015. determine the normal depth, critical depth, velocity and the froude number.

  Determine the weight of bar for distance between two base

The bar is 1m long and its weight, W, acts at its midpoint. The angle is a=30 degrees, and the the spring constant k= 100N/m. The spring in its current position is 1.52m long, and its unstretched length of 1.25 m occurs when the bar is vertical a=..

  Determine its velocity for t along a straight line

A particle moving along a straight line is subjectd to a deceleration a=(-2v^3)m/s^2 where v is in m/s. If it has a velocity v=8 m/s when t=0, determine its velocity when t=4s.

  Determine what ph results when mole of nah are added

The temperature = 25°C; assume that u = 10^-2 after the addition. Compare the value obtained when ionic strength effects are taken into account with that calculated when it is neglected.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd