Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
An AISI 4140 OQT 1000 sleeve is to be secured to a 2.50-inch diameter solid rod ot the same material employing a class FN1 force fit. The outside diameter of the sleeve is 5.00 inches.
a) Calculate the interface pressure at the maximum limit of interference for this class of fit.
b) Calculate the corresponding tensile stress at the inner surface of the hole in the sleeve.
c) How much must we raise the temperature of the sleeve to shrink fit the sleeve onto the rod? Give answer in degrees Fahrenheit.
Design an 8-bit register with 2 control inputs s1 and s0, 8 data inputs I7..I0, and 8 data outputs Q7..Q0. s1s0=00 means maintain the present value, s1s0=01 means load, and s1s0=10 means clear. s1s0=11 means to swap
The solar constant at Earth orbit (1 AU = 1 Astronomical Unit - Sun-Earth distance) is ~1400 Watts/m2. Assuming that this Poynting flux magnitude can be associated with a single E- and Hfield (i.e., E × H ),
An underdamped sensor with a static sensitivity of K=1, undamped natural frequency of omega=1400 rad/s, and damping ratio of zeta=0.5 is used to measure a sinusoidal signal with a frequency of 6 kHz.
A 15 hp, 209V,three-phase,six pole, Y-connected induction motor has the following parameter values per phase: R1= 0.128 ohm, R'2=0.0935 ohm Xeq- X1 + X'2 = 0.49 ohm. The motor slip at full load is 3%, and the efficiency id 90%.
A 1 kHz sine wave signal with a power level -10 dBm is applied to the input of the amplifier. What is the power at the amplifier output in dBW?
S = {c(k + jl) | k = 3, 1, 1, 3 and l = 3, 1, 1, 3 and j = square root of -1, where c is a constant. Determine the value of c to ensure a unit energy constellation. Sketch this constellation. Find d^2 min and label the constellation points with bi..
Design an RC-Low Pass Filter with cutoff frequency at fc=0.5GHz and plot its frequency response and design a parallel resonance circuit with resonance frequency of 30kHz and bandwidth of 20kHz and plot its frequency response.
at the frequency f=12khz, a filter is designed to attenuate the input signal by 78db, find the amplitude of the output signal if the 12khz input has an amplitude of 1V.
Write a script that determines whether an amino acid is going to bind to a certain molecule. It is know that the first region (1-5) of the molecule binds strongly to amino acids A, C, I, L, Y and E, and weakly to W, S, M, G, and K.
For a new product sales are expected to be 2,000 products in year 1, increasing by 1,000 products each subsequent year to 5,000 products in year 4. Two different manufacturing equipment options are available a) Up front equipment purchase cost of $..
1. What are some of the fundamental differences between ladder logic programs and relay logic diagrams 2. What are the advantages and disadvantages of a PLC simulation software with virtual input
A) Compare and contrast the following serial bus architectures: I2C, CAN, UART. Discuss the hardware implementation, communication protocol, and typical applications of each. B) Explain the concept of bit dominance used in CAN bus.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd