Calculate convection coefficients for flows of water and air

Assignment Help Mechanical Engineering
Reference no: EM131281643

An electric resistance heater is embedded in a long cylinder of diameter 30 mm. When water with a temperature of 25°C and velocity of 1 m/s flows crosswise over the cylinder, the power per unit length required to maintain the surface at a uniform temperature of 90°C is 28 kW/m. When air, also at 25°C, but with a velocity of 10 m/s is flowing, the power per unit length required to maintain the same surface temperature is 400 W/m. Calculate and compare the convection coefficients for the flows of water and air.

Reference no: EM131281643

Questions Cloud

Is the wall under steady-state conditions : Calculate the heat flux from the interior air to the wall, from the wall to the exterior air, and from the wall to the interior air. Is the wall under steady-state conditions?
Are employers who provide references to prospective employee : Are employers who provide references to prospective employees presumed to be acting in good faith unless a lack of good faith is shown by clear and convincing evidence?
Direction of change for the quantity : Can we determine with certainly the direction of change for the quantity? For the price? Explain briefly.
Describe a wan in terms of uses, ownership and span. : Describe a MAN network, in terms of its uses, ownership, and span (how much area is covered).Describe a WAN in terms of uses, ownership and span.
Calculate convection coefficients for flows of water and air : Calculate and compare the convection coefficients for the flows of water and air.
Above or below equilibrium for long : Explain why the price in a free market will not remain above or below equilibrium for long, unless there is outside interference.
Evaluate the convection coefficient at the instant of time : evaluate the convection coefficient at the instant of time when the plate temperature is 225°C and the change in plate temperature with time (dT/dt) is 0.022 K/s. The ambient air temperature is 25°C and the plate measures 0.3 × 0.3 m with a mass o..
Should the union bring the issue to arbitration : The union has asked you for advice on how to challenge the testing program. - Should the union bring the issue to arbitration? The NLRB? The courts? Advise the union and explain.
What is total daily service cost for the single teller model : Bank Boston has a branch at Bryant College. The branch is busiest at the beginning of the college year when freshmen and transfer students open accounts. What is the total daily service cost for the single teller model?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd