User Account

All Pages

Calculate centre line temperature

Assignment Help Mechanical Engineering
Reference no: EM13965394

A large steel plate 5 cm thick is initially at a uniform temperature of 400oC. It is suddenly exposed on both sides to a surrounding at 60oC with convective heat transfer co-efficient of 285 W/m2K.

Calculate the centre line temperature and the temperature inside the plate 1.25 cm from themed plane after 3 minutes.

Take K for steel = 42.5 W/mK, ? for steel = 0.043 m2/hr.

Reference no: EM13965394

Questions Cloud

Calculate the heat transfer per unit width of the plate : Calculate the heat transfer per unit width of the plate. Assuming the length of the plate along the flow of air is 2m.
Results of a statistical study : It is believed that the effects of smoking differ depending on race. The following table gives the results of a statistical study for this question.
Show that orthogonal transformation preserves dot product : Show that the orthogonal transformation preserves the dot product i.e Au dot Av = u dot v. Hence or otherwise show that the angles between 2 vectors are preserved under the orthogonal transformation.
Salaries of male and female professors : Assume that the salaries of male and female professors are both normally distributed with equal standard deviations.
Calculate centre line temperature : Calculate the centre line temperature and the temperature inside the plate 1.25 cm from themed plane after 3 minutes.
Normally distributed populations : The following information was obtained from two independent samples selected from two normally distributed populations with unknown but equal variances.
Prepare schedules of cost of goods manufactured : Prepare schedules of cost of goods manufactured and cost of goods sold and an income statement.
Difference between the two population means : At the conclusion of the instructional period, a reading test gave results y1 = 74, y2 = 71, s1 = 9, and s2 = 10. What is the attained signi?cance level if you wish to see if there is evidence of a real difference between the two population means?..
What does the formal job analysis process consist of : Based on your research, what specific selection method might you use for selecting the best candidate for the job, and why? What are two advantages and two disadvantages of this method?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The pressures of the nitrogen are low enough to treat it as

nitrogen gas is flowing in a 50mm diameter pipe at the rate of 0.05kgs. the nitrogen flows through a partially closed

  Determining the systolic and diastolic pressures

Are the systolic and diastolic pressures reported in blood pressure measurements absolute, gage, or vacuum pressures? When the instrument panel of a car provides the outside air temperature, where is the temperature sensor located?

  Determine the temperature and the total enthalpy in the

20 kg of r134 a at 300 kpa fills a rigid container whose volume is 28 l. determine the temperature and the total

  Studying the performance of wire-coatingdies

Show that the result in (c) can be written as a "plane slit" formula multiplied by a "curvature correction." Problems of this kind arise in studying the performance of wire-coatingdies.

  In an experiment similar to the procedure set out for part

in an experiment similar to the procedure set out for part a of the calorimetry experiment 1.500 g of mgs was combined

  Determine the mass of the requested machinery fluid

An oil drilling operation has requested a machinery fluid F containing 86.0% lubricant, 8.0% corrosion control, and 6.0% detergent for its drilling rigs. You plan to produce the fluid by recycling two existing machinery products. Product A contains 9..

  What is the work done and the entropy generated for process

What is the work done and the entropy generated for the process that is a rigid container with volume 200 L and is divided into two equal volumes by a partition with both sides containing nitrogen, one side is at 200 kPa, 100oC and the other side is ..

  Calculate the cooling water flow rate in the vessel c that

2000 kgh of milk is sterilized in a steam infusion sterilizer steam and milk directly contact. the milk is heated to

  Komodo dragons are the largest lizards known to man

Komodo dragons are the largest lizards known to man. A 250-pound dragon can eat enough food to increase it body weight by 1/2. Which number sentence could be used to find w, the weight of a k0modo dragon after increasing it body weight by 1/2?

  Find pin dynamic forces and torque

Find: Pin dynamic forces and T (torque applied on link 2 ) to generate the required input velocity following requested output velocity of 25rpn Please note that for kinetic analysis

  If the flow rate of water is measured to be 03 m3s

water is pumped from a lower reservoir to a higher reservoir by a pump that provides 21 kw of shaft power. the free

  When delivering 10 amps to an external load the voltage

a battery can be modeled as an ideal source with an internal resistance - a constant voltage source with the resistor

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd