Calculate capacitance and charge on capacitor

Assignment Help Electrical Engineering
Reference no: EM132909787

Question

The energy stored in a certain capacitor when connected across a 400 V d.c. supply is 0.3 J. Calculate: (a) the capacitance; and (b) the charge on the capacitor.

Reference no: EM132909787

Questions Cloud

Record the transactions in the books of pictou : Record the above transactions in the books of Pictou based on dates. If there is no journal entry for Pictou at specific date, indicate No for the specific date
Supply current when impedances are connected in parallel : If the supply voltage remains unchanged, calculate the supply current when the impedances are connected in parallel.
Series circuit consists of non-inductive resistor : A series circuit consists of a non-inductive resistor of 10 O, an inductor having a reactance of 50 O and a capacitor having a reactance of 30 O.
Calculate the inductance and capacitance of circuit : The bandwidth of a series resonant circuit is 500 Hz. Calculate the inductance and capacitance of the circuit.
Calculate capacitance and charge on capacitor : Calculate the capacitance and the charge on the capacitor.
Node voltage technique : The Node Voltage technique (Nodal analysis) lends itself to circuit models having current instead of voltage sources.
Resistances of equivalent delta-connected resistors : Calculate the resistances of equivalent delta-connected resistors.
Strategies to change and strengthen organizations culture : Explain four strategies to change and strengthen an organizations culture such as: actions of founders and leaders, culturally consistent rewards, Selecting and
Explain the factors of influencing on team effectiveness : Explain the factors of influencing on team effectiveness for high performance team (give simple answer with short example)

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Compare your results to those obtained from a microwave cad

If possible, compare your results to those obtained from a microwave CAD tool.

  Calculate the smallest nominal output voltage step

Calculate the nominal offset voltage range (when the pot. Is adjusted over its full range). This is independent of the effects of the output due to the counter. Calculate the smallest nominal output voltage step (use nominal values of the resistors..

  Determine what is the total charge q on the disk

The electrical potential at the center of a uniformly charged circular disk of radius R=3.5cm is V0 =550 V. What is the total charge q on the disk

  How to minimize the number of inputs to the and gate

Using a 4-bit synchronous counter and an AND gate, construct a counter that counts from 0000 through 1010. Repeat for a count from 0000 through 1110. Minimize the number of inputs to the AND gate.

  Derive a lorenz curve for loserville

a. From the information provided, please derive a Lorenz Curve for Loserville. Show graphically.

  Determine the voltage induced in the wire segment

A 20-cm length of wire moves at 15m/s in a constant flux density of 0.4T. The wire, direction of motion, and direction of the flux are mutually perpendicular. Determine the voltage induced in the wire segment.

  What is the resolution of an 8-bit dac

Which of the following is not an advantage of SPI transmission over SCI transmission Error checking via parity bit Faster transmission Master-slave capability Synchronous transmission A HCS12 embedded timer is in PWM mode.

  Define the value of the complex constant a

Suppose that we define the value of the complex constant A as A = -2 + 2j. Write the constant A in magnitude-angle form, that is, find |A| and A such that A = |A|ej A Sketch the real part of the function z(t), where z(t) = Aej(500pit+pi/2).

  Determine the number of turns of wire in the secondary coil

A 22000 V, 60 Hz generator is connected to the high voltage side of a 22000-2200V, 500 kVA step down transformer. If the resultant core flux is 0.0683 Wb (max), determine: A) the number of turns of wire in the secondary coil.

  Find the magnetic field and inductance

A 1000 turns wire are tighly wound on a toroid with a rectangular cross section, the heigh of toroid is 0.5 cm . The inner and outer radii of 2 cm and 3cm respectively. The current in the wire I=100 mA, Ur = 4000. N= 1000, Find H,B,phi and inducta..

  Explain with the aid of sketches

Explain with the aid of sketches and by using an example of a specific logic family, what is meant by the term noise immunity

  Define subroutine which generates 8 bit random numbers

Write an assembly code for a subroutine implementing signed multiplication with Booth's algorithm. Make sure it works as expected. Compare it with your implementation of sign/magnitude multiplication from the second homework.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd