Calculate assume constant specific heat of cp024 btulbmr

Assignment Help Mechanical Engineering
Reference no: EM13601677

Consider an ideal simple gas turbine cycle. For a net power output of 10,000 horse power, an inlet air temperature of T1=500 R, an inlet turbine temperature of T3=2000 R, and a compression ratio of 10, calculate: (assume constant specific heat of Cp=0.24 Btu/lbm.R and k=1.4) a) The compressor exit temperature (T2) and the turbine exit temperature (T4), b) The air mass flow rate, and c) The cycle efficiency.

Reference no: EM13601677

Questions Cloud

The credit balance in the allowance for uncollectible : sullivan co.s accounts receivable show the following balances by ageage of receivable balance0-30 days 60000031-60 days
The mix leaves the chamber at 200kpa and 70 dgree clecius : water at 200 kpa and 10 degree celcius enters a mixing chamber at a rate of 150 kgmin where it is mixed steadily with
A 25g bullet pierces a sand bag 27cm thick if the initial : question a 25g bullet pierces a sand bag 27cm thick. if the initial bullet velocity was 64 ms and it emerged from the
Case 14-35 comparison of alternatives using net present : case 14-35 comparison of alternatives using net present value analysis kinglsey products ltd. is using a model 400
Calculate assume constant specific heat of cp024 btulbmr : consider an ideal simple gas turbine cycle. for a net power output of 10000 horse power an inlet air temperature of
Compute the unit product costs for one gamelan if company : compute the unit product costs for one gamelan if company uses absorption costing and variable costing.ida sidha karya
Spacely sprockets company manufactures a high-tech : spacely sprockets company manufactures a high-tech component that passes through two production processing departments
Slick corporation is a small producer of synthetic motor : slick corporation is a small producer of synthetic motor oil. during may the company produced 5000 cases of lubricant.
If there is a firm with assets that will convert to cash in : if there is a firm with assets that will convert to cash in the next 12 months in excess of its obligations to pay cash

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the horizontal line along

Determine (a) the horizontal line along which the shearing stress is a maximum, (b) the constant k in the following expression for the maximum shearing stress.

  What is the angular velocity wcd

What is the angular velocity Wcd (t)?

  Explain the different experimentpurpose of this practical

explain the different experiment.purpose of this practical is to verify the law for parallelogram of forces law for

  Determine vertical distance between two consecutive drops

Water drips at the rate of 5 drops per second from a leaking tap. Determine the vertical distance between two consecutive drops after the lower drop has attained a velocity of 3 m/s.

  Determine the pressure in the evaporator

Describe IN DETAIL how you could determine the required rate of heat addition or removal.

  Determine the work input and the amount of heat rejected

The cylinder of a water-cooled reciprocating compressor contains 0.05m^3 of air at 1.01bar. It is compressed isothermally to 8.0 bar. Determine the work input and the amount of heat rejected to the compressor cooling water.

  Determine the magnitude of the initial velocity

determine the magnitude of the initial velocity of the bullet and the magnitude of the force exerted by the bullet on the block.

  Pulley system and motor

The 50-lb load is hoisted by the pulley system and motor M. If the crate starts from rest and by constant acceleration attains a speed of 15 ft/s after rising s = 6 ft, determine the power that must be supplied to the motor at this instant.

  Heat is transferred to the steam until the temperature

A piston-cylinder device has a volume of 0.1 cubic meters and contains 0.5kg of steam at 0.4 MPa. Heat is transferred to the steam until the temperature is 300 degrees Celsius

  The packages slide along the surface abc to anbspconveyor

packages are thrown down an incline at a with a velocitynbspof 1 ms. the packages slide along the surface abc to

  Calculate the velocity and acceleration of collar a

In the position shown, the angular velocity and the angular acceleration of the rod AB are 4 rad/sec and 6 rad/sec2, respectively, both counterclockwise. For this instant calculate the velocity and acceleration of collar A. ( AB = 600 mm)

  Calculate the final pressure and volume of the system

The process and volume relation is given p=(8-4v)bar for a non flow process ,where V is in cubic meter.If 130kJ of work is supplied to the system,calculate the final pressure and volume of the system.Take the initial volume as 0.5 cubic meter.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd