Calculate and plot the distribution of total and effective

Assignment Help Civil Engineering
Reference no: EM13543369

A borehole at a site reveals a soil profile comprising 6 m deep fine sand layer overlying a 9 m thick clay layer, which in turn overlies weathered bedrock. The groundwater table is located at a depth of 4 m from the ground surface. A zone of capillary saturation exists in the fine sand layer above the groundwater table. Above the zone of capillary saturation, the fine sand layer can be considered to be dry. The air entry value (AEV) for fine sand layer is 15 kPa and its specific gravity (Gs) and porosity (n) are 2.65 and 0.315, respectively. The natural water content (w) and void ratio (e) of the clay layer are 28.5% and 0.7, respectively. The unit weight of water (γw) is equal to10 kN/m3

a. At what depth from the ground surface is the top of the capillary saturation zone located?

b. Calculate and plot the distribution of total and effective vertical stresses as well as pore-water pressure with depth from the ground surface up to the bedrock surface.

Reference no: EM13543369

Questions Cloud

How many tons of aggregate will be needed : The allowable stress in a steel shaft with an outside diameter of 1.5in and an inside diameter of 1.1in is 12,000psi. What hp can the shaft deliver at 1750rpm?
What is the maximum number of phases that may be present : For a ternary system, three components are present; temperature is also a variable. What is the maximum number of phases that may be present for a ternary system, assuming that pressure is held constant?
What is the maximum tension in the cable due to the 6-k load : Where should a single 500-lb live load be places on the beam so it causes the largest live moment at D? What is this moment? Assume the support at A is fixed, B is pinned, and C is a Roller
Determine the initial void ratio assume also that settlement : A square building (15 m × 15 m in plan) is to be constructed on a site where the soil profile consists of 3m of clay with an over-consolidation ratio that varies from 5 at the surface to 2 at 3m overlying a 5m thick clay
Calculate and plot the distribution of total and effective : Calculate and plot the distribution of total and effective vertical stresses as well as pore-water pressure with depth from the ground surface up to the bedrock surface.
Determine the minimum time needed for the plate temperature : Consider a 1000-W iron whose base plate is made of 0.5 cm thick aluminum alloy 2024-T6 (density = 2770 kg/m^3 and c(p)=875 J/kg C). The base plate has a surface area of 0.03 m^2. Initially the iron is in thermal equilibruim with the ambient air at 22..
Societal changes and juveniles : Write a brief description of two societal changes that influence today''s juveniles and explain how. Then explain how and why the societal changes you described might contribute to juvenile delinquency
Compute the friction force acting on the block : A 2.20-kg block starts from rest at the top of a 30.0° incline and slides a distance of 2.10 m down the incline in 1.60 s. Find the friction force acting on the block
Application-treatment programs : Explain how each program is influenced by sociological, biological, and/or psychological factors thought to contribute to juvenile crime and delinquency. Be specific and use examples to support your explanation.

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is its density when saturated

Prove that Ev=kP for an isentropic fluid process given that constant=P/p^k, where p is the density (roe), P is the pressure, k is the ratio of specific heats.

  The initial and after-consolidation void ratio of the sample

A saturated sample of soil, 38mm in diameter and 75mm high, hasbeen prepared for a triaxial test. Total mass of the sample was measured as 144.6grams, and the initial moisture content determined at 25.2%. The Specific Gravity of thesolids was estimat..

  What would the height of a water tower with a gallon tank

what would the height of a water tower with a 500 gallon tank have to be, to bring water ( by gravity ) from sealevel over a distance of 2.5miles with an elevation of 300ft

  What are the volumetric flow rates of the two outlet streams

A permeation membrane separates an inlet air stream (79 mol% N2, 21 mol% O2) into a permeate stream and a reject stream. The inlet stream conditions are 293K, 0.5 MPa and 2 mol/min; the conditions for both outlet streams are 293 K and 0.1 MPa.

  Determine rate of increase of speed and the normal force

sled and rider with a total weight of 200 lb travel down smooth slope defined by equation y=x^2/20. At x=40 ft the sled's speed is 10 ft/s. At x=40 ft determine rate of increase of speed and the normal force which the slope exers on the sled.

  Determine what error results from curvature and refraction

Successive plus and minus sights taken on a downhil line of levels are listed below. the values represent the horizontal distances between the instrument and either the plus or minus sights.

  Determine ft and fn

for this purpose replace this force by its equivalent of two forces at At Ft parallel and Fn perpendicular to the beam. Determine Ft and Fn.

  Determine discharge-q and depth of flow in the gutter

The continuity equation is just the water balance for the slope or any small portion of the slope and can be given as: p - fp = RO where i = rainfall rate, fp = infiltration capacity, and RO = runoff rate, all expressed as a depth per time

  What is the speed of the bug as seen by the man at the side

A bug is crawling up the leg of a man on a train. The velocity of the bug relative to the man is 0.3 m/s k . The mas is waling from one side of a carriage to the other with a vlocity relative to the train of 1.2 m/s j.

  How many of the incinerators in chicago meet the standard

Stack gas samples were collected from a sample of 50 incinerators in Chicago. Of the 50 samples, only 18 met an environmental standard for the concentration of a hazardous compound. Can it be concluded that fewer than half of the incinerators in C..

  Predict the temperature required in an isothermal plug flow

Using the method of Lee et al., predict the temperature required in an isothermal plug flow incinerator to reduce the xylene level in a waste gas from 100 ppm to 10 ppm. Assume a residence time of 0.7 sec.

  Select a parshall flume capable ofmeasuring a flow of 700 ft

Assuming a gage reading in the approach well(haa) of 13 ft, select a Parshall flume capable ofmeasuring a flow of 700 ft/s without submerging the flow.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd