Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Chemical Engineering
1. A stream containing 4wt% chromium (Cr), is contained in the wastewater from an absorber. The wastewater stream is fed to a treatment unit that removes 95% of the chromium in the feed and recycles it to the plant. The residual liquid stream leaving the treatment unit is sent to a waste lagoon. The treatment unit has a maximum capacity of 4500 kg wastewater/hr. If wastewater leaves the finishing plant at a rate higher than the capacity of the treatment unit, the excess (anything over 4500kg/hr) bypasses the unit and combines with the residual liquid leaving the unit, and the combined stream goes to the lagoon.
a) Without assuming a basis of calculation, draw and label a flowchart for the process.
b) Wastewater leaves the finishing plant at a rate between 1000kg/hr and 10000kg/hr. In increments of 1000kg/h, cacluate the flow rate of liquid to the waste lagoon, and the mass fraction of chromium in the liquid over the given range. Using a graphing program (MATLAB, Excel), generate a plot of the flow rate as a function of mass fraction.
Design a Linde process to liquefy oxygen. Pure oxygen is supplied at 1 bar, 25 °C and liquid oxygen is received at 1 bar. The fluid is compressed to 150 bar in a series of compressors whose efficiency is 80%. Precooling is done by water at 20 °C. ..
Risk Analysis and Management: Fragility versus Loads and Fire Explosion Safety Issues, 1. A propane tank is located 100 m away from the nearest buildings. The fragility to explosion can be expressed by
The partition that divides the cylinder is removed and the contents are allowed to reach equilibrium without heat losses to the surroundings. Determine the pressure and temperature in the final state assuming steam to be an ideal-gas. Is ideality..
When a smooth hump is installed across a flowing flume, free surface level drops. How do you classify the initial flow? Explain the reasons for changes in flow depth near the hump using concepts of specific energy and total energy. Use the Es-Y di..
Two watt meters are used, as shown in Figure 4.3.1, to measure the power absorbed by a balanced delta-connected load. Determine the total power in kW, the power factor, and the per-phase impedance of the load if the supply-system voltage is 120
Calculate the heat when 100.0 mL of 0.500 M HCl is mixed with 300.0 mL of 0.100 M Ba(OH)2. Assuming that the temperature of both solutions was initially 25.0C and that the final mixture has a mass of 400.0 g and a specific heat capacity of 4.18 J..
Determine the pinch temperature and the minimum utility requirements for the process set out below. Take the minimum approach temperature as 15 °C. Devise a heat-exchanger network to achieve maximum energy recovery.
Neglect leakage and fringing, and consider the iron to be infinitely permeable. The coil has 1000 turns and carries a direct current of 3 A. Compute the pull on the plunger for g = 1.25 cm.
chalf its rated kVA at 0.85 power factor lagging.
A W12x22 structural steel wide-flange section of ASTM A36 steel is used as an axially loaded column. Find the allowable axial compressive load using Euler's formula and a factor of safety of 2.0. The column is pin connected at both ends and is 15 ..
The adipic acid plant described in Examples 9.5 and 9.9 is to be built in China, with a location factor of 0.85. The cost estimate needs to be updated from 2006 to 2012. Up to 45% of the total investment can be secured as a low-cost loan at an int..
Sinusoids of varying frequencies were applied to an open loop system and the following results were measured. (Data is from Seidel, 1975.) Construct a Bode diagram for the data.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd