By what percentage is the capacity of the flume reduced

Assignment Help Civil Engineering
Reference no: EM13297860

A Parshall Flume is to be designed to measure the discharge in a channel. If the design flowrate is 1m^3/sec, determine the width of the flume to be used such that the depth of flow immediatly upstream of the throat under design conditions is 1 m. By what percentage is the capacity of the flume reduced if the downstream depth is 0.85m?

Reference no: EM13297860

Questions Cloud

Calculate the cost per equivalant unit for assuming : Calculate the cost per equivalant unit for assuming that labor is added unformally throughout the production process?
Analyzing the financial statements : After analyzing the financial statements and thoroughly researching a company, you have realized that the firm has had zero interest-bearing debt (no notes, bonds, or loans) over the past eight years.
Discuss the trend for each ratio : Discuss the trend for each ratio and what it tells you about an organization's financial health.
Determine the downstream water level to produce the flowrate : The flow through an 8 ft. Parshall Flume is 129 cfs when Ha is 2.50 ft. Determine the downstream water level (Hb) that would produce this flowrate.
By what percentage is the capacity of the flume reduced : determine the width of the flume to be used such that the depth of flow immediatly upstream of the throat under design conditions is 1 m. By what percentage is the capacity of the flume reduced if the downstream depth is 0.85m
State injected into the mixture and the total pressure jumps : An equilibrium mixture of PCl5(g), PCl3(g), and Cl2(g) has partial pressures of 217.0 Torr, 13.2 Torr, and 13.2 Torr, respectively. A quantity of Cl2(g) is injected into the mixture, and the total pressure jumps to 263.0 Torr (at the moment of mix..
Find what fraction of the population would make per year : Suppose there were reason to believe that incomes in some population were normally distributed, with a mean of $47,000 per year, and a standard deviation of $5,500 per year.
Select an exclusion from income : Please select an exclusion from income. Explain the exclusion and its purpose. What do you think the congressional intent was for this exclusion?
Assemblies can be stored in global assembly cache : Which of the following assemblies can be stored in Global Assembly Cache?

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the tce concentration in ppm if the tank is held

What is the TCE concentration in ppm if the tank is held at (a) 4 degrees C and (b) 35 degrees C (c) What is the TCE concentration in ppm if the tank is filled with hexane instead of water

  Determine the volume flow rate of water

Water with a static pressure of 1.96kN/M 2 flows through an 800 mm diameter pipe. A pitot tube pressure gage in this pipe reads a pressure of 5.88 kN/M 2 . How do you determine the volume flow rate (Q) of the water? (Q = 1.40 M^3/sec, V=2.79 M/se..

  Determine the power that must be supplied

determine the power that must be supplied to the motor at this instant. The motor has an efficiency of 76 %. Neglect the mass of the pulleys and cables.

  Unit of measurement and unit of payment

Write the unit of measurement and unit of payment of following items. 1) Earthwork in excavation in foundation. 2) Framwork. 3) Steelwork in trusses. 4) Damp proof course D.P.C. 5) Cement.

  Principal stresses and the orientation of planes

A direct shear test is performed on a saturated specimen of loose sand. A normal stress equal to 100 kPa is applied and a maximum shear stress of 75 kPa is measured in the shear test. Determine the principal stresses and the orientation of these p..

  Calculate the ratio of area to volume for unit cube

calculate the ratio of area to volume for unit cube a unit sphere in inscribed inside the cube, and as write cylinder inscribed inside the cube.

  Find the minimum dimension of the other side

The modulus of elasticity of the wood is 13GPa. If one side of the column is 25cm across, find the minimum dimension of the other side to keep the column's deformatin under 1.3 mm

  Design a single angle strut connected to a gusset plate

Design a single angle strut connected to a gusset plate to carry 180k n factored load. The length of the strut between center to center intersection is 3m.

  Conductive heat loss through the furnace wall

Assuming unit surface area, find the conductive heat loss through the furnace wall and the temperature at the interface of the fire clay and red brick.

  Pharmaceutical mixing tank

In year one, a pharmaceutical mixing tank had a market price of $120,000. It replaced an older smaller mixing tank that had a BV of $15,000.

  Estimate the change in pressure over 100 m of pipeline

Water at 20 degrees flows at a velocity of (V =) 2 m/s in a (D =) 250-mm diameter horizontal ductile iron pipe. Estimate the friction factor f in the pipe, and state whether the pipe is hydraulically smooth or rough.

  Find the increase in vertical stresses due to the weight

The center to center spacing to the two tanks is 14 m. The new tank imparts 150 kPa at the ground surface. Find the increase in vertical stresses due to the weight of the two tanks mid- way between the two tanks at the center of the clay layer.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd