Buoyant device used for measuring specific weight of liquid

Assignment Help Mechanical Engineering
Reference no: EM13708154

A hydrometer is a buoyant device used for measuring the specific weight of a liquid. A weighed glass bulb floats below the surface with a graduated stem extending above the surface. The position of the fluid level on the steam corresponds to the specific gravity of the fluid. Given a hydrometer with a cylindrical bulb that has a diameter of 2 cm and a length of 8cm. The cylindrical stem has a diameter of 1 cm and a length of 8 cm. The mass of this instrument is 35 g. What is the range of specific gravities that can be measured with this hydrometer?

Reference no: EM13708154

Questions Cloud

Drip irrigation problem : Drip irrigation is a means of getting water directly to growing plants with very little waste. One method uses a large-diameter polyethylene "mother" tube (10-15 mm i.d.) from which lead many small diameter polyethylene feeder tubes, called drippers,..
Block of copper at at initial temperature : A 25-kg block of copper at at initial temperature of 150 C equilibrates with 0.79 kg of liquid water at an initial temperature of 20 C in an insulated tank. If the average specific heat of copper can be taken to be 0.395 kJ/kg.K, determine the final ..
The raw material price and consumable price : Within the last month, the raw material price and consumable price combined has increased by 5.5%. If the throughput was 5 parts/hour estimates the future throughput that has to take place in order to maintain a constant production cost. Consider the..
Compressor is employed to compress gas : A compressor is employed to compress gas flowing steadily through it. The gas enters the compressor at a temperature of 16°C, a pressure of 100 kPa, and with an enthalpy of 391.2 kJ/kg. The gas leaves the compressor at a temperature of 245°C, a pre..
Buoyant device used for measuring specific weight of liquid : A hydrometer is a buoyant device used for measuring the specific weight of a liquid. A weighed glass bulb floats below the surface with a graduated stem extending above the surface. The position of the fluid level on the steam corresponds to the spec..
Determine the final pressure and the quality-boundary work : A piston-cylinder device initially contains 0.15-kg steam at 3.5 MPa, superheated by 5C. Now the steam loses heat to the surroundings and the piston moves down, hitting a set of stops at which point the cylinder contains saturated liquid water. The c..
Describe the failure pattern of a ductile material in shear : Describe the failure pattern of a ductile material in shear, and predict the failure pattern of a ductile mater material under torsion.
Fluid flow through a non-circular cross-section pipe : The pipe flow experiment deals with fluid flow through a non-circular cross-section “pipe”. Please explain, using supporting equations, HOW you would calculate the pressure loss during fluid flow between two points along the pipe.
A material has a strength coefficients : A material has a strength coefficients K = 100, 000 psi Assuming that a tensile-test specimen made from this material begins to neck at a true strain of 0.17, show that the ultimate tensile strength of this material is 62,400 psi.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd