Build a home security system circuit using this program the

Assignment Help Electrical Engineering
Reference no: EM13380195

Build a home security system circuit using this program. The system must include a door sensor,window sensor, smoke detector, water leak sensor, a motion detector.

There also must be a keypad included into the schematic. A code (for example, 5411) must first be entered into the key pad in order to be able to arm the sensors throughout the home (and disarm as well).

Once the command is made to arm the sensors, there will be a period of 15 seconds until the sensors are active.

Reference no: EM13380195

Questions Cloud

Q1consider the following codedefine add1-iter a-listnbsp : q1consider the following codedefine add1-iter a-listnbsp define add1-helper curr-list result-listnbspnbspnbspnbspnbsp
1 draw a plan of a typical strip mine showing all : 1. draw a plan of a typical strip mine showing all operational features and equipment.2. answer the followinga. why is
Part a a brawl in mickeys backyardread the discussion case : part a a brawl in mickeys backyardread the discussion case a brawl in mickeys backyard question 1 in a chart diagram or
Modern automotive paint plants use water-bornefinishes to : modern automotive paint plants use water-bornefinishes to minimize the emission of volatile organiccompounds vocs from
Build a home security system circuit using this program the : build a home security system circuit using this program. the system must include a door sensorwindow sensor smoke
Relationship to learning outcomescritically analyse the : relationship to learning outcomescritically analyse the theory concepts and models of operations and information
Case study questionspart a 1 how is tesla different to : case study questionspart a 1. how is tesla different to other car manufacturers in terms of concept design and
Reading oakland j s 2003 tqm text with cases case study 4 : reading oakland j. s. 2003 tqm text with cases case study 4 pp. 379-389. 3rd ed. oxford butterworth-heinemann. and
In 2001 a chennai- based two- wheeler major introduced a : in 2001 a chennai- based two- wheeler major introduced a bonus scheme for its employees. employees covered under this

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What will be the final amounts of saturated vapor and water

A tank of 0.52 m3 capacity is filled with steam at 2 MPa and 350oC. The tank and its contents are slowly cooled to 125oC. Answer the following questions assuming that there was a negligible volume change during the cooling process

  Determine and plot the three-phase current commands

In a 2-pole, three-phase PMAC drive, the torque constant and the voltage constant are 0.5 in MKS units. A constant torque of 5 Nm is developed to bring the system from rest to 5000 rpm in 5 seconds.

  Determine the modulation index and percentage modulation

When unmodulated the carrier voltage is 75 volts peak. An information (modulating) signal of 15 KHZ with 5 volts peak amplitude causes a frequency deviation of 22.5 KHz. If the load resistor RL= 100 Ohms, determine the following Modulation index

  Determine slip at which the motor develops maximum torque

Use Matlab to verify the above results and determine: a. The starting torque b. The maximum torque c. The slip at which the motor develops maximum torque d. Draw the torque-speed characteristic of the motor

  How much current is flowing through the resistor

If I have a resistor that is 10 Ohms and has a voltage drop of 4.2 V, how much current is flowing through the resistor?

  Show the relative uncertainty in volumetric flowrate

Water is flowing out of a tube at a near constant volumetric flowrate, V .If a graduated cylinder is used to collect a certain volume, v , of the water, and a timer is used to measure the time, t, required to collect the volume of water, the volum..

  Could voltage create problems for other customers requiring

Assume the acceptable deviation is +- 5.8%. Thus, a nominal rms voltage of 120 V will range from 113 to 127 V. Suppose the line to line voltage at Customer A is 13.8kV, the load at customerA consumes complex power (1.2+j1.2)x 10^6 W.

  Determine the force exerted on a point charge q1

Find the force exerted on a point charge Q1 by the point charges Q2 andQ3. Assume that Q1 =2.5[nC], Q2 = -12.0[nC], andQ3= -1.7[nC] are located at (0,-1,2)[m],(1.5,2,-1)[m],k and (-1,-1.5,2)[m], respectively.

  Calculate total charge on plates and potential gradient

The capacitance of a capacitor formed by two parallel metal plates each 200 cm2 in area separated by a dielectric 4 mm thick is 0.0004 microfarads. A p.d. of 20,000 V is applied. Calculate (a) the total charge on the plates

  Obtaining a d-latch and in each case draw the logic diagram

The D-Latch is constructed with four NAND-gates and an inverter. Consider the following three other ways for obtaining aD-Latch, and in each case draw the logic diagram and verify the circuit operation

  Determine the transmitter power from a transmitting antenna

The power density 50km from a transmitting antenna is 0.5 uW/m^2. If the frequency is 2 GHz and the antenna gain is 30 dB, determine the transmitter power.

  Each pole of a 100kw 250v flet-compound generator has a

each pole of a 100kw 250v flet-compound generator has a shunt field of 2000 turns and a series field of 7 turns. if the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd