Reference no: EM131990591

Networking Assignment: Wireshark Capture Filter

Part 1 - Wireshark and traffic capture basics

Describe what the term promiscuous mode means in relation to capturing network traffic with Wireshark and similar network traffic analysers.

The Capture > Options dialog allows the Name Resolution of Network Layer names. Describe what this means and describe how it could be used for capturing network traffic.

Describe the difference between a network switch and a network hub. Then explain how switched networks limit the network traffic that is visible to Wireshark in comparison to networks that used hubs. (Note - switches are the technology used in today's computer networks)

In TCP/IP networking IP addresses are used to identify specific computers (or hosts) on the network, clients use ports numbers to specify a particular instance of a client program (for example a specific tab on a web browser) and servers normally use well known port numbers on which to listen for client requests. For instance ftp at the server uses ports 20 and 21.

From the web or any other source determine the well-known port numbers of the following server programs:

• ftp data
• ftp control
• http
• NTP
• ssh

Also find the well know port numbers for 6 other network protocols and describe the function that each protocol performs.

Part 2 : Capture filters

In this section of the assignment you are required to learn the syntax for creating Wireshark Capture Filters. Then document and use capture filters to capture specific network traffic.

Discussion of Berkeley Packet Filter (BPF) syntax

The following discussion gives a brief explanation of the BPF syntax to help you get started with constructing your own capture filters.

Wireshark capture filters use the Berkeley Packet Filter (BPF) syntax to specify particular traffic. This syntax is used by the libpcap (in Unix/Linux) and Winpcap (in Windows) libraries that are used by Wireshark to capture network traffic.

Note - WinDump is the Windows version of a Linux/Unix program called TCPDump and hence TCPDump documentation applies to capture filter syntax as used on Windows machines.

Syntax

The BPF syntax consists of one or more Primitives that specify a particular type of traffic to capture.

Some examples of simple primitives are shown below:

(i) host 192.168.12.22
(ii) host google.com
(iii) src host google.com
(iv) tcp port 80

Things to note about these primitives:

• Primitives start with one or more qualifiers (eg. host, src host, dst host etc.)
• Primitives end with an ID (eg. 192.168.12.22, google.com, 80 etc.)

Note - If you use named IDs like google.com then you need to enable name resolution in the capture filter dialog box when specifying capture filters.

In summary a capture filter consists of one or more primitives and those primitives consist of one or more qualifiers followed by an ID.
{ <------- primitive ------> } { operator } { <- primitive -> }
dsthost 192.168.12.13&&tcp port 80

The references dst, host, tcp and port are called qualifiers.

The references 192.168.12.13 and 80 are called ID's.

The boxed example above also shows the AND operator being used to join two primitives to make a capture filter expression. The AND operator isone of the three possible operators that are allowed in capture filters, the other two are ORand NOT.

Sources of documentation of the Berkeley Filter Syntax that you should refer to are:

Documentation that describes the BPF syntax.
There are also good cheat sheets for TCPDump (Wireshark Capture Filters) and Wireshark Display filters.

The Wireshark Users Guide (Access from Help in Wireshark)

End of discussion of BPF syntax

Documenting BPF qualifier syntax

There are three types of BPF qualifiers:

• Type (3)
• Dir (2)
• Proto (8)

The Type qualifier has three possible options: host, net andport. The other two qualifier types also have associated options, there are 4 options associated with Dir qualifier type and 8 options associated with Proto qualifier type(please disregard the fddi, decnet options as they are seldom used in today's networks).

You are required to describe what each qualifier means and list a total of 10 capture filter examples that incorporate at least 1 qualifier and one ID, and explain how each capture filter works.

Documenting the 3 logical operators for combining primitives

The boxed example above show the logical AND operator ( && ) being used to combine two primitives. There are two other such logical operators.

Document all three logical operators and give one example of how each could be used in a capture filter.

Implementing BPF capture filters

In this section of the assignment you are required to create a range of capture filters, implement those capture filters in Wireshark and take a screenshot of associated captured traffic.

Your screen captures must include the Time, Source, Destination and Protocol fields of the Wireshark display along with at least two packets (the graphic below shows three, packets 7,8 & 9).

Because the Time field is displayed to such a fine resolution your screenshot capture will be unique from all other students doing this assignment. This will therefore act as an automatic plagiarism detector.

After creating an appropriate capture filter you may need to generate appropriate traffic for Wireshark to capture. For instance, if you create a Capture Filter to capture ftp traffic you will need to run an ftp client to effect the traffic capture. Likewise, when capturing web traffic you could use a browser to generate appropriate traffic. To capture ICMP traffic you might use the ping command because it uses the ICMP protocol to query other hosts.

Example capture filter:

Filter requirements

Capture all traffic between your computer (that is running Wireshark) and the Google search engine in response to the query "caviar" being entered.

Procedure:

Open a browser to www.google.com

From the Wireshark interface select:

Capture > Options >

Select the desired interface (or select all interfaces)

Enter host google.comin the capture filter entry area

Select the display option Resolve network layer names

Start the capture

Then enter the word caviar into the google query field of the browser

Wireshark will captures the require traffic.

Note - Make sure you have selected the correct network interface, or select all interfaces if you are unsure.

Capturing traffic from/to another machine (2 marks)

In network analysis you will frequently need to capture all traffic or specific traffic between your machine that is running Wireshark and another specified machine.

For this exercise you should generate traffic between the machines with the ping command.

Create capture filters that will:

1. Capture all traffic between your machine (the one running Wireshark) and another machine. Use the IP address of the other machine to identify it in the filter.

2. Capture all traffic between your machine (the one running Wireshark) and another machine. Use the MAC address of the other machine to identify it.

3. Capture all traffic from the other machine. Use either the IP or MAC address of the remote machine to identify it.

4. Capture only ICMP traffic between the two machines

Your discussion for this section should:

• include two screenshots
• list all capture filters you used
• describe how each capture filter works.

Excluding particular network traffic (2 marks)

Create a set of capture filters that will:

• Capture broadcast traffic only
• Exclude broadcast traffic
• Capture all traffic from a range of network addresses but exclude broadcast traffic

Briefly discuss how each capture filter works.

Using port numbers in capture filters

Create capture filters that will capture the following types of network traffic:

1. DNS traffic
2. DNS traffic being sent from your machine
3. DHCP traffic in either direction

Briefly discuss how each capture filter works.

Challenge exercise

The BPF syntax can detect specific content at specific offsets from the start of network packets.

An example of such syntax would be tcp[13] & 4 == 4

This particular capture filter can detect TCP packets that have the RST flag set.

Describe this syntax so that a layman could understand how such filters work.