User Account

All Pages

Boundary-layer thickness

Assignment Help Mechanical Engineering
Reference no: EM13886471

A laminar boundary layer of 20-C atmospheric air moving at 2 m=s exists on one side of a 2-m-wide, 3-m-long ?at plate. At x ¼ 3 m ?nd:

(a) The boundary-layer thickness.

(b) The wall shear stress.

(c) The maximum y-component of velocity.

(d) The drag force.

(e) The displacement and momentum thicknesses.

(f) The ?ow rate through the boundary layer.

Reference no: EM13886471

Questions Cloud

Calculate the length of the entrance region : A 4-mm-diameter horizontal, 40-m-long pipe is attached to a reservoir containing 20-C water. The surface of the water in the reservoir is 4 m above the pipe outlet. Assume a laminar ?ow and estimate the average velocity in the pipe. Also, calculat..
Narrowly defined aspect of american history : The end product should not be a comprehensive study of a topic but rather a focused examination of a specific theme (a microhistory) that you choose based on your reading of the documents that your research uncovers, and the history written about the..
Potential liability for the auditor or audit firm involved : The following are five independent situations.
Comment on perceptions of quality of nfas oversight of pfg : Comment on your perceptions of the quality of the NFA's oversight of PFG. Do you think it is ethically problematic that Wasendorf served on an advisory committee of the NFA?
Boundary-layer thickness : A laminar boundary layer of 20-C atmospheric air moving at 2 m=s exists on one side of a 2-m-wide, 3-m-long ?at plate. At x ¼ 3 m ?nd:
Estimate the thickness of the boundary layer : It is assumed that a boundary layer begins to develop about 12 km from shore. If the wind speed averages 18 m=s, estimate the thickness of the boundary layer and the shear stress on the surface of the water near the shore.
Darwin''s concept of evolution become dangerous : When does Darwin's concept of evolution become dangerous?  Should Darwin's theory of evolution apply to all living creatures? Provide examples of when Darwin's theory of evolution have gone beyond the scientific realm to the political realm.
Consider compliance with laws and regulations : 1.Explain the auditor's responsibility to consider compliance with laws and regulations.
Turbulent ?ow from the leading edge : Water at 20-C ?ows over a 3-m long and 2-m wide ?at plate at 3 m=s. Assume a turbulent ?ow from the leading edge (a trip wire at the leading edge can be used to cause the turbulence) and calculate:

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the total work done to the system steam what is the

determine the heat transfer necessary to increase the pressure of 70 percent quality steam from 200 to 700 kpa

  For the refrigerant as the system w -056 btu kinetic and

refrigerant 134a is compressed with no heat transfer in a piston- cylinder assembly from 30 lbfin2 20 degrees f to 160

  Steam at 10mpa and 300c with a mass flow rate of 10kgs

steam at 1.0mpa and 300c with a mass flow rate of 10kgs enters an insulated turbine operating at steady state and exits

  Determine the final pressure of the gas

Helium gas is contained in a rigid vessel of 0.5 m3 at 500 kPa. The gas is agitated violently by a stirrer that transfers 250 kJ of work to the gas. Assuming that the system undergoes an adiabatic process, determine the final pressure of the gas. Ass..

  A thermocouple is located 1 m from the leading edge of a

a thermocouple is located 1 m from the leading edge of a flat plate along which water flows at 1 ms. the distance

  Determine the volume of the tank

Determine a) the volume of the tank,b)the final temperature and pressure, and c) the internal energychange of the water.

  Generalized mass and energy conservation equations

Steam at 2.5 MPa and 400 C enters an adiabatic steam turbine with a low velocity and leaves with a velocity of 180 m/s at a pressure of 15 kPa and a quality of 90 percent. Assume steady state for the current problem state. Neglect potential energy.

  Design value for the molded friction material and steel disk

Design value for the molded friction material and steel disks to be used 0.06 and pressure max=1400kpa. Determine appropriate values for the disk inside dimmeter, the total number of disks and the actuating force?

  Compare the minimum theoretical rate and the actual rate at

at steady state. a power cycle generates 100 mw of electricity while discharging energy by heat transfer at a rate of

  Heat transfer occurs until the volume on the inside of the

a piston-cylinder device contains 1 kg of h2o. the water is at 800oc and a pressure of 20 mpa. heat transfer occurs

  Hexagonal close-packed crystal structure

Consider a hypothetical metal that has a hexagonal close-packed crystal structure and an atomic weight of 70.28 g/mol. If the atomic radius is 0.1473 nm and the c/a ratio is 1.723, then calculate (a) the unit cell volume, and (b) the density of the m..

  Drawing outlet and inlet valves for a compressor

The question related to Mechanical Engineering and the question is about drawing outlet and inlet valves for a compressor for controlling compressor. The symbols have been drawn with standard ISA symbols

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd