Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A thin film waveguide has n1 = 1, n2 = 1.5 and n3 = 1.462. The waveguide thickness is 0.9 μm.Light from a He-Ne laser (λ0 = 632.8 nm) is being guided in the (fundamental) TE0 mode, for which the effective refractive index of the guide is neff = 1.481, If a 45° -45°-90° prism with index np = 2.25 is used as an output coupler, what angle will the exiting beam make with the surface of the waveguide?
A. find the sixtieth percentile B. Find the seventy fifth percentile C. Determine the number of data points that fall between the sixieth and seventy fifth percentiles you found in parts A. and B.
Calculate the maximum power that can be sent through an a=2cm , b=1cm air-filled waveguide at 12 GHz such that dielectric breakdown does not occur. Assume that the dielectric strength of air at atmospheric pressure is 3x10^6 [V/m]
One colomb is the total charge associated with 6.242*10^18 electrons. How many electrons will pass through a conductor if 50 microamperes of current flows for 5 seconds
A load ZL is connected to the secondary of a linear transformer that is characterized by inductance's L1 = 1 H and L2 = 4 H and a unity coefficient of coupling. If w(omega) = 1000 rad/s, find the equivalent series network (R, L, and C values) seen..
Determine the temperature in the middle of the bar and evaluate it at t = 1, 2, 3, 10, 50 sec. First guess, and then calculate. Also, plot the temperature expression vs. time from t = 1 to 50 sec using Excel
What would be the minimum allowable sampling rate for a pulse-duration modulator if it is required to handle a baseband frequency range from 50 Hz to 10 kHz
A 600V, dc shunt motor has an armature and field resistance of 1.5 ohm and 600 ohm, respectively. When the motor runs unloaded, the line current is 3A, and the speed is 1000 rpm.
A "Hall bar" specimen is 250 mm long, 12 mm wide, and 1.5 mm thick. Along the 250 mm direction (+x), +5 V drives a current of +1.75 mA. Along the 1.5 mm direction (+z) a magnetic field of 1 Tesla is applied.
Calculate the approximate quantization S/N ratio in the baseband audio signal at the receiver output (after the DAC and LPF).
A cable technician tested the signal-to-noise ratio on the curb as 20 dBm. This means, if the noise power is at 1 mW, then the signal power should be 20 dB higher then that. If the noise power is 20 mW
Design and sketch a band pass filter consisting of an RC high-pass filter with a cutoff frequency of 300 Hz and an RC low-pass filter with a cutoff frequency of 700 Hz. Carefully select the R and C of each filter so that one filter does not load t..
Given A series RLC linear circuit with an inductor1 of 0.5 Henry, followed by a capacitor 0f 0.01 Farad, followed by another inductor2 of 0.5 Henry and a resistance of 10 Ohms. 1 Specify the input impedance of this circuit Z(s).
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd