Bcc or the fcc crystal structure

Assignment Help Mechanical Engineering
Reference no: EM131106836

1-An x-ray diffractometer recorder chart for an element that has either the BCC or the FCC crystal structure shows diffraction peaks at the following 2θ angles: 400, 580, 730, 86.80, 100.40, and 114.70. The wavelength of the incoming x-ray used was 0.154 nm.

a) Determine the Bravais lattice of the element.
b) Determine the lattice constant, a of the element.

1882_1.png

 2-A copper-target x-ray tube is operated at 40,000 volts and 25mA. The efficiency of an x-ray tube is so low that, for all practical purposes, one may assume that all the input energy goes into heating the target. If there were no dissipation of heat by water-cooling, conduction, radiation, etc., how long would it take a 100-gm copper target to melt? 

(Melting point of copper = 1083OC, mean specific heat = 6.65 cal/mole/OC, latent heat of fusion = 3,220 cal/mole.) 

3-Filters for Co K radiation are usually made of iron oxide (Fe2O3) powder rather than iron foil. If a filter contains 5 mg Fe2O3/cm2, what is the transmission factor for the Co K? line? What is the intensity ratio of Co K? to Co K? in the filtered beam? 

Density of Fe2O3 = 5.24 gm/cm3,

?/? of iron for Co K? radiation = 59.5 cm2/gm,

?/? of oxygen for Co K? radiation = 20.2 cm2/gm,

?/? of iron for Co K? radiation = 371 cm2/gm,

?/? of oxygen for Co K? radiation = 15.0 cm2/gm. 

4- Determine the values of 2? and (hkl) for the first three lines (those of lowest

2? values) on the powder patterns of substances with the following structures, the incident radiation being Cu K?: (4 points)

(a) Simple cubic (a = 3.00Å)

(b) Simple tetragonal (a = 2.00 Å, c = 3.00 Å)

(c) Simple tetragonal (a == 3.00 Å, c = 2.00 Å)

(d) Simple rhombohedral (a = 3.00 Å, ? = 80O) 

4- Plot the reciprocal lattice for a polycrystalline sample of a material with a simple tetragonal structure and lattice parameters a=4.0Å and c=5.0 Å.

 5-What strain is required to produce the same broadening as a crystallite size of 5nm? 

6-Using Bragg ‘s law, calculate the diffraction angles (2?) for the first three peaks in the aluminum thin film.

7-Show that the structure factor, I is independent of the shape and size of the unit cell.

8-Calculate the velocity and kinetic energy with which the electrons strike the target of an x-ray tube operated at 50K volts. What is the short-wavelength limit of the continuous spectrum emitted and the maximum energy per quantum of radiation?

  9-Plane A is represented on a stereographic projection by a great circle passing through the N and S poles and the point 00 N, 700W. The pole of plane B is located at 300N, 500W.

(a)Find the angle between the two planes.

(b)Draw the great circle of plane B and demonstrate that the stereographic projection is angle-true by measuring With a protractor the angle between the great circles of A and B.

2210_1.png

Find out the magnitude of the maximum non-uniform yield stress required to produce the same broadening as a crystallite size of 5nm if the elastic modulus is equal to ?. Ignore instrumental effect and make necessary assumptions. 2423_1.png

Reference no: EM131106836

Questions Cloud

What impact would the following changes : What impact would the following changes have on the security market line and therefore on the required return for a given level of risk? (a) An increase in inflationary expectations. (b) Investors become less risk-averse.
What are the forecasted levels of notes payable : What are the forecasted levels of notes payable and special dividends? What are the forecasted levels of the line of credit and special dividends?
Explain the meaning of each variable in the capital asset : Explain the meaning of each variable in the capital asset pricing model (CAPM) equation. What is the security market line (SML)?
Use this material to discuss and explore : Mid-termThe Mid-Term paper is based on your readings and assignments so far from this class. Use this material to discuss and explore what you think the current White House economic stimulus plan for transportation will have on the U.S. transporta..
Bcc or the fcc crystal structure : 1-An x-ray diffractometer recorder chart for an element that has either the BCC or the FCC crystal structure shows diffraction peaks at the following 2θ angles: 400, 580, 730, 86.80, 100.40, and 114.70. The wavelength of the incoming x-ray used was 0..
Paper on special issues in communication : Write a 1,050- to 1,400-word paper on special issues in communication. Discuss the following in your paper as they relate to communication: Diversity and Ethics
Verify the validity of the chapman-kolmogorov identity : Using this example, verify the validity of the Chapman-Kolmogorov identity.
The amount of pressurization in an airline cabin : Passenger comfort is influenced by the amount of pressurization in an airline cabin. Higher pressurization permits a closer-to-normal environment and a more relaxed flight. A study by an airline user group recorded the corresponding air pressure o..
Compute the probability that exactly ten requests : The number of requests for assistance received by a towing service is a Poisson process with average of 4 requests per hour*. a) Compute the probability that exactly ten requests are received during a particular 2 hour period.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd