Based on the above conditions determine the error when the

Assignment Help Mechanical Engineering
Reference no: EM13618905

A pressure transducer that behaves as a second order system is used to monitor pressure fluctuations in a petrochemical pipeline. It is designed to have an undamped natural frequency of 4000 Hz. However, because it is damaged its damping ratio is unknown. When the transducer is subjected to a harmonic input of 2400 Hz, the phase angle between the output and input is measured at 45 degrees.

i.) Based on the above conditions, determine the error when the transducer is used to measure a harmonic pressure signal of 1600 Hz.

ii.) What is the phase angle between the input and output at this frequency?

iii.) Using excel obtain plots of the frequency response and phase response to harmonic excitation signal of 5000 Hz base conditions sited in the problem statement. Is the transducers' response characteristics suited to the application?

Reference no: EM13618905

Questions Cloud

Weisbro and sons common stock sells for 23 a share and pays : weisbro and sons common stock sells for 23 a share and pays an annual dividend that increases by 4.5 percent annually.
The illinois lottery has an instant game that promises 25 : the illinois lottery has an instant game that promises 25 top prizes of 1 million each. in the small print it says that
Leslies unique clothing stores offers a common stock that : leslies unique clothing stores offers a common stock that pays an annual dividend of 2.30 a share. the company has
The average income tax refund for 2009 tax year was 3095 : the average income tax refund for 2009 tax year was 3095. assumes the refund per person follows the normal probability
Based on the above conditions determine the error when the : a pressure transducer that behaves as a second order system is used to monitor pressure fluctuations in a petrochemical
For a sensible heater that provides 100000 btuhr and : for a sensible heater that provides 100000 btuhr and increases the air temperature 35 f determine the volumetric flow
What would be the radius of the arc followed by a proton : a deuteron particle the nucleus of an isotope of hydrogen consisting of one proton and one neutron and having a mass of
Scores on a national exam assume a normal distribution with : scores on a national exam assume a normal distribution with a population mean of 50 and population standard deviation
A standardized third grade reading test called the we can : a standardized third grade reading test called the we can read test has a mean of 50 with a standard deviation of 10. a

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Problem 110degc water is flowing in a 10-mm diameter smooth

problem 110degc water is flowing in a 10-mm diameter smooth tube. the mass flow rate of the water is 0.15 kgs. the

  Determine the temperatures of surface 1 through 4 of the

determine the temperatures of surface 1 through 4 of the furnace cavity of example 13.3 if the entire furnace

  What is the pressure drop associated with the airflow

What is the total rate of heat transfer to the air? What is the pressure drop associated with the airflow?

  The radial loads of both gears are in the same plane and

a shaft is to be designed to support the spur pinion and helical gear shown in the figure on two bearings spaced 700 mm

  The desire is to raise the temperature of the ambient air

The desire is to raise the temperature of the ambient air from 60 degree F to 350 degrees F ---- I need to calculate the amount of steam energy in BTU's per minutes and lbs of steam per minute necessary to accomplish the increase in air temperatur..

  For the same electrical output what is the percent

a fossil-fuel steam power plant operates at about 50 of carnot thermal efficiency. it has been suggested that the air

  Determine the pressure in the evaporator

Describe IN DETAIL how you could determine the required rate of heat addition or removal.

  Determine the expressions for the principal stresses

A circular shaft is subjected to a torque Ta and a bending moment Ma. Assuming that the diameter of the shaft is d, determine the expressions for the principal stresses and maximum shear stress in terms of Ma, Ta and d.

  What is the required wheel diameter to overcome

an industrial water shutoff valve is designed to operate with 30 lb of effort force. The valve will encounter 200 lb of resistance force applied to a 1.5 in. diameter axle. what is the required wheel diameter to overcome the resistance force?

  A heat exchanger is to be designed to condense 1100 kghr of

a heat exchanger is to be designed to condense 1100 kghr of steam ay 150 kpa. for this purpose cooling water at 50

  Calculate the maximum power of the wind on each site in kw

two sites are being considered for wind power generation. on the first site the wind blows steadily at 7 ms for 3000

  Calculate the incidence it of the tailplane for trim if the

calculate the incidence it of the tailplane for trim if the elevator deflection e is zero. ii calculate the neutral

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd