Atmospheric air can be modeled as ideal gas moisture

Assignment Help Mechanical Engineering
Reference no: EM13713278

Atmospheric air can be modeled as ideal gas moisture at a temperature T0 and pressure P0. At a particular location the mole fractions are of the ideal gas components of the mixture are xoN2= 0.7567 xoH20= 0.0303 xoO2= 0.2035 xC02= 0.0003. Consider a process by which 1 mole of O2 is extracted from the atmospheric air mixture. The end result of this operation is a 1 mole batch of pure O2 at T0 and P0. Determine the minimum work to perform this task. Also show that this work requirement is greater than the minimum work that compared to N2

Reference no: EM13713278

Questions Cloud

Theoretical air and burned : Methane (CH4) is mixed with 125% theoretical air and burned.
Kind of problem an angular momentum-impulse equation : Explain in 4 to 5 sentences at least in what cases/in what kind of  problem  an angular momentum-impulse equation and concept can be reduced  to conservation of angular momentum. Give an example of a problem where conservation of angular momentum is ..
Decorative water fountains consist of a water reservoir : Decorative water fountains consist of a water reservoir and underground piping to and from a pump. One such system is shown schematically in the figure. The pipe material is PVC(a table is provided). The outlet line from the pump is 18 m and the inle..
Assume that the vapor is an ideal gas : A compressed liquid mixture of 42 mol percent n-hexane (1) and 58 mol percent ethane (2) is to be fed to a flash tank where the pressure is reduced and a liquid and vapor stream separated. The flashing operation will be carried out at 32°C.
Atmospheric air can be modeled as ideal gas moisture : Atmospheric air can be modeled as ideal gas moisture at a temperature T0 and pressure P0. At a particular location the mole fractions are of the ideal gas components of the mixture are xoN2= 0.7567 xoH20= 0.0303 xoO2= 0.2035 xC02= 0.0003. Consider a ..
Is the deformation of the silicone case elastic or plastic : A women dropped dropped her iPhone 1,400-feet when taking a picture on a plane. A few days later it was returned to her by a stranger - and the best part is it still works. The iphone is covered by a silicone case as shown in the picture below.
Determine heat transferred through the reactor walls : Consider combustion of hydrogen in pure oxygen under constant pressure in a two-inlet and single-exit reactor. The reactants enter the reactor at temperature T1 = 200 K. The products leave the reactor at temperature T2 = 2000 K. No work is developed ..
Expand to fill the entire container at constant temperature : Determine the change in entropy for 1.0 mole of an ideal gas originally confined to one-half of a 5.0-L container when the gas is allowed to expand to fill the entire container at constant temperature.
Ratio between longitudinal and lateral deformations : At the proportional limit, a 30 mm wide × 12 mm thick bar elongates 2.0 mm under an axial load of 41.5 kN. The bar is 1.5-m long. If Poisson’s ratio (ratio between longitudinal and lateral deformations) is 0.33 for the material, determine:

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What are different types of nuclear reactors

What are different types of Nuclear reactors in operation in thev world.

  Consider fully developed constant-property laminar flow

consider fully developed constant-property laminar flow between parallel planes with constant heat rate per unit of

  Two slender rods of negligible weight are pin-connected at

two slender rods of negligible weight are pin-connected at a and attached to the 18-lb block b and the 80-lb block c as

  Create the speed-torque curve and torque-current curve

A particular motor has the following specifications: no load speed = 5000 rpm, stall torque = 200mN-m, no load current = 0.25 A, rated operating = 2500 rpm, 100mN-m, 5A. Create the speed-torque curve, torque-current curve, power-torque curve, and det..

  In the system below for measuring fluid viscosity the inner

in the system below for measuring fluid viscosity the inner cylindrical core is stationary the outer cylindrical shell

  A hydraulic lift system utilizes two 3 in diameter

a hydraulic lift system utilizes two 3 in. diameter cylinders. workers must determine how much the system is capable of

  A uniform beamoflength l flexural rigidity ei and

a uniform beamoflength l flexural rigidity ei and cross-sectional plastic moment mp is built-in at both ends and

  Duct flow is modeled by steady dimensional velocity field

Converging duct flow is modeled by the steady two-dimensional velocity field. For the case in which Uo = 3.56 ft/s and b = 7.66s^-1, Plot several streamlines from x = 0 to 5 ft and y = -2 to 2 ft. Be sure to show the direction of the streamlines.

  How many engagement points on the flywheel

a full revolution press has 100 rpm flywheel rotation.it has two handed trip devices mounted 20 inches from point of operation how many engagement points on the flywheel would be nessary to make this machine safe?

  Steam at 3 mpa 500c enters an insulated turbine operating

steam at 3 mpa 500c enters an insulated turbine operating at steady state and exits at 0.3 mpa. determine the maximum

  The pressure at the end of the bend is 70 pounds per square

a 4 foot diameter pipeline carries water at a temperature of 60 f at a steady flow rate of 40 cubic feet per second.

  Use 3 terms of taylor series to estimate the velocity at

the velocity of falling parachute is computed asvtgmc 1-e-cmtwhere g9.8ms2 m50kg c12.5.use 3 terms of taylor series to

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd