At what time t2 has 50 percent of the initial energy stored

Assignment Help Electrical Engineering
Reference no: EM13277688

A 100μF capacitance is initially charged to 1000 V. At t1=0, it is connected to a 1kΩ resistance. At what time t2 has 50 percent of the initial energy stored in the capacitance been dissipated in the resistance?

Reference no: EM13277688

Questions Cloud

Determine the total charge induced on the conducting plane : Two dielectric media with dielectric constants ε1 and ε2 are separated by a plane boundary at x = 0, A point charge Q exists in medium 1 at distance d from the boundary. a - Verify that the field in medium 1 can be obtained from Q and an image char..
A balance the equation for this reaction in acidic solution : Complete and balance the equation for this reaction in acidic solution. ZnS + NO3^- -> Zn^2+ + S + NO Which element was Oxidized. Which element was reduced ? Which species was the oxidizing agent ? Which species was the reducing agent
Find the amount by which the length of the stack decreases : A copper cylinder and a brass cylinder are stacked end to end, as in the drawing. Find the amount by which the length of the stack decreases
Explain the melting point apparatus near tmelt : One of the most common causes of inaccurate melting points is too rapid heating of the melting point apparatus near Tmelt. Under these circumstances, how will the observed melting point compare to the true melting point
At what time t2 has 50 percent of the initial energy stored : A 100μF capacitance is initially charged to 1000 V. At t1=0, it is connected to a 1kΩ resistance. At what time t2 has 50 percent of the initial energy stored in the capacitance been dissipated in the resistance
How high does the ball rebound : A 210g ball is dropped from a height of 1.8m and bounces on a hard floor. How high does the ball rebound
Design a static cmos circuit for a 4-bit comparator circuit : Design a static CMOS circuit for a 4-bit comparator circuit. The comparator circuit takes 2 bit strings as inputs, and returns the larger one. For example, for the inputs 0100 and 0011, the circuit will return 0100.
Determine the acceleration of the man : Two skaters, a man and a woman, are standing on ice. Neglect any friction between the skate blades and the ice. Determine the acceleration (magnitude and direction) of the man
Compute the equilibium concentration of i2 : In analysis of interhalogen activity, 0.110 mol of ICl was placed into a 1.00 L flask and allowed to decompose at a high temperature: 2 ICl(g) I2(g) + Cl2(g) Given that Kc = 0.361, calculate the equilibium concentration of I2

Reviews

Write a Review

Electrical Engineering Questions & Answers

  How many decibels is system inferior to dsb- sc modulation

The average noise power per unit bandwidth measured at the front end of an AM receiver is 10^(-3) watt per Hertz. The modulating wave is sinusoidal, with a carrier power of 80 kilowatts, and a sideband power of 10 kilowatts per sideband.

  Whether an fet is operating in ohmic region or active region

Discuss the operation of a JFET, including the pinch off and gate-source cutoff voltage in your explanation. Discuss how you can tell whether an FET is operating in the ohmic region or the active region.

  Find the speed of the block after it has slid 190 m

The magnitude of the acceleration of the block is 1.93 m/s^2 (a) Find the coefficient of kinetic friction between block and plane? I got 0.393 but it is wrong. (b) Find the speed of the block after it has slid 1.90 m

  How to convert numbers to 4-bit values

Convert both numbers to 4-bit values, take the 2's complement of 9 and add them. What happens to the carry out How does that compare with what happens when you subtract 8 from 9

  How long does doping take for an average hole to drift

A Si bar is 0.25 cm long and 500 ?m2 in cross-sectional area. It is grounded at x=0 and biased at +20V at x=0.25 cm. Find the resistance and the current at 300K (a) when the Si bar is doped with 2×1017 cm-3 arsenic

  Design amplifier ckt that will amplify the conversations

Design an amplifier circuit that will selectively amplify dolphin social conversations. The microphone can be modeled as a sinusoidal voltage source with peak amplitude less than 15 mV in series with a 1 ohm resistor.

  Determine system bandwidth for subcarrier frequency spacing

An OFDM system employs 260 data subcarriers, 40 pilot subcarriers, and 34 guard subcarriers to transmit data through a wireless channel. QPSK modulation is employed for each subcarrier.

  Determine what is the phase current of the load

A balanced Y-connected power system is known to have Van=100

  Discuss key quantities from a zener diode data sheet

Discuss some key characteristics of "load lines". What information does a load line provide you. Discuss key quantities from a zener diode data sheet. What are most important for a circuit designer.

  Determine the insertion loss when feeding a matched load

n a symmetrical T attenuator pad, each series arm has a resistance of 35-ohm and the shunt arm has a resistance of 110. Determine a. the characteristic impedance b. the insertion loss when feeding a matched load c. the A B C D constants of t..

  Draw the gate-level diagram

Write the logic equation for Y in terms of A,B,C that solves this problem, and draw the gate-level diagram.

  Write canonical product-of-sum expression for f in shorthand

Consider the function f which has four inputs a,b,c,d and one output such that the output is a 1 if and only if the number of 1s in the inputs is even. (a) Write the canonical product-of-sums expression for f. Do not use the shorthand notation

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd