At what power factor would synchronous generator be running

Assignment Help Mechanical Engineering
Reference no: EM131315340

In a small generating system, there are two generators in parallel. One of them is a synchronous generator, and the other, an IG. The common load is 3.0 kW with a power factor of 0.92.

If the IG supplies only 1.0 kW of the total load at a power factor of 0.85, at what power factor would the synchronous generator be running?

Reference no: EM131315340

Questions Cloud

What is the bottle neck of the process : Activity B takes 5 minutes and is performed by Aaron and Betty together. Activity C takes 4 minutes and is performed by Betty and David. Activity D is performed by David and takes 3 minutes. What is the bottle neck of the process?
Advise investing money to put this engine on market : An inventor claims to have developed an engine that takes in 100,000Btu at a temperature of 400 K, rejects 40,000 Btu at a temperature of 200 K, and delivers 15kW . h of work. Would you advise investing money to put this engine on the market?
Prepare a multi-step plan for the agency : This extended discussion (300-400 words) will require you to draw on several competencies you have acquired as you have progressed through this course - Identify a potential ethical violation that may be harming Kara.
Why do you think hp paid so much for autonomy : Based on your experiences and other readings why do you think HP paid so much for Autonomy? Was it a doomed strategy, or was it a good idea that did not pan out?
At what power factor would synchronous generator be running : If the IG supplies only 1.0 kW of the total load at a power factor of 0.85, at what power factor would the synchronous generator be running?
Lean thinking and management philosophy : Provide an analysis of the relationship between lean thinking and management philosophy that explains how lean thinking supports a management philosophy that addresses not only production practices, but also the roles and responsibilities of manag..
Discuss about the nutrition and physical activity log : Discuss about the Nutrition and Physical Activity Log.The PowerPoint presentation should consist of 15-20 slides detailing the topic. Be creative, specific, and informative. Each teacher educator candidate will be graded on the following: knowledge..
Evaluate the maximum torque in n m : Evaluate The maximum torque in N m, The slip factor at the maximum torque, The torque to generate the rated voltage and Full-load torque.
Introduction summarizing the criminal and case : Your essay should have an introduction summarizing the criminal and case, a body that discusses the issues surrounding the case (how were they able to avoid being caught for so long - personality of the offender, lack of evidence available, lack o..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine expressions for the temperature gradient

The heat flux is known to be constant. Determine expressions for the temperature gradient and the temperature distribution when the surface at x = 0 is at temperature T1.

  The base of the tank and strikes

Water flows through a 2 cm opening in the side of a tank. If the opening is 8 m below the surface of the water,what volume of a water would escape from the tank per minute?If a stream of water escapes from another hole 2 m above the base of the tank ..

  Determine the forces in the marked members

Determine the force in member CH of the truss - Determine the forces in the marked members "F2 and F1" of the truss.

  The surface of the apple is 84 degrees c what is the heat

an apple with the following properties weight 2.7 n diameter0.0921 m volume0.000325 m3 is cooled to a uniform

  Determine an expression for the fundamental axial mode shape

Determine an expression for the fundamental axial mode shape, φi(x), and use M a t l a b , or another computer program, to plot the fundamental mode. Scale the mode so that.its maximum value is l.CL

  A smooth sheet metal duct of rectangular section 075ft by

in an air-conditioning installation a flow rate of 1750 cfm of air at 50 degree ferenheit is required. a smooth sheet

  Three seconds after a polisher is started from rest small

three seconds after a polisher is started from rest small tufts of fleece from along the circumference of the

  Resultant force and couple moment

The bricks on top of the beam and the supports at the bottom create the distributed loading shown in the second figure. Determine the required intensity w and dimension d of the right support so that the resultant force and couple moment about poin..

  Calculate the quality if saturated or the temperature if

steam enters an insulated nozzle with a velocity of 500 ms and a pressure of 5.0mpa and a temperature of 600 degrees

  Water circulating in a water jacket enclosing the compressor

Air, modeled as an ideal gas, is compressed at a steady state from 1 bar, 300 K, to 5 bar, 500k with150 kW of power input. Heat transfer occurs at a rate of 20 kW from teh air to cooling water circulating in a water jacket enclosing the compressor. N..

  Determine the rate of heat loss from the engine

Determine the rate of heat loss from the engine, its entropy production rate and Its entrance and exit specific flow availabilities.

  Solid steel shaft d 20mm is subjected to a torque of 1200nm

solid steel shaft d 20mm is subjected to a torque of 1200nm. what size hollow circular steel shaft could be used to

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd