At what point or points on y-axis is electric potential zero

Assignment Help Electrical Engineering
Reference no: EM13262899

A -3.4 nC charge is on the x-axis at x_1 = -8 cm and a 4.6 nC charge is on the x-axis at x_2 = 17 cm.

At what point or points on the y-axis is the electric potential zero?

Reference no: EM13262899

Questions Cloud

What recommendations would you make to aunt tillie : Aunt Tillie has deposited $33,000 today in an account which will earn 10 percent annually. She plans to leave the funds in this account for seven years. If the goal of this deposit is to cover a future obligation of $65,000, what recommendations w..
At most how many 1-operand instructions can be formulated : A computer has 16-bit instructions and 64 registers. Suppose it is required to have at least 14 instructions designed to have 2 operands from registers (e.g., add, $1, $3 puts the sum of $1 and $3 into $1.
Distinguish data from information : Distinguish data from information and describe the characteristics used to evaluate the quality of data.
Find the direction and magnitude of the ferrys velocity : A passenger walks from one side of a ferry to the other as it approaches a dock. what are the direction and magnitude of the ferry's velocity relative to the water
At what point or points on y-axis is electric potential zero : A -3.4 nC charge is on the x-axis at x_1 = -8 cm and a 4.6 nC charge is on the x-axis at x_2 = 17 cm. At what point or points on the y-axis is the electric potential zero
In which direction is the wave traveling : An electromagnetic wave has an electric field given by E? (y,t)=[ 3.60×105V/m cos(ky?(1.250×1013rad/s )t)]k^. In which direction is the wave traveling
Find the power and rms value of each of the signals : The problem has two parts(a and b) and it asks: Find the power and rms value of each of the following signals: a) x(t) = 5 + Ccos(ωot+θ) b) x(t) = 2+7cos(1/2t+θ1)+3cos(2/3t+θ2)+5cos(6t+θ3)
Find the energies of the four lowest states : An electron in a 1-D box of length 0.100 nm, Find the energies of the four lowest states that have energies above the ground states
Design a compensator that gives a pm of 90 degrees : Given that KG =.0894, w=15.4, φ=-125 degrees and G(s) = [520(s+2)]/[s2(s+30)] design a compensator that gives a PM of 90 degrees and does not change the open loop bandwidth.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Develop the ow-graph for the fft algorithm from the radix-2

Develop the ow-graph for the FFT algorithm from the radix-2 FFT algorithm for the N = 9 case in which the input is in the bit-reversed order and the output is in normal order.

  What will be segment base that will map to physical address

If the segment base 002Bh with offset 0013h maps to physical address 002C3h in memory, what will be the segment base that will map to same physical address 002C3h using an offset of 0003h

  Find the bandwidth of modulated signal using carsons rule

a- for this modulator a 1-v signal produces a deviation of 20Khz determine the amplitude and phase spectra of s(t) for the modulating signal m(t) = 1.5 cos(2*pi*6*10^4*t) when fc>>fm b- find the bandwidth of the modulated signal using carson's rule..

  What device width is needed to ensure the minimum resistance

A switch is made with an n-channel MOS device in a technology for which oxide thickness is 20 nm, minimum channel length is 1 um, unCox = 100 uA/V2, and VTH = 0.8 V. The devices operates in deep triode (i.e. small VDS)

  Calculate the increase in units of decibels

A)An amplifier has an input voltage of 0.5V and an output voltage of 12V.Calculate the increase in unit decibels. B)An amplifer has an input power 2W and an output power of 80W. Calculate the increase units of decibels.

  Determine the errors in serial transmission

A serial transmission is set up for 8 bits with odd parity. The first two bytes of data are 01110111 with parity bit 1 and 01101010 with parity bit 0. From this we know that there are no errors in transmission.

  Compute the voltage indicated

resistor: a volt-ohmmeter with an internal impedance of 1000 Ω/V and an EVM with an impedance of 11 MΩ. Calculate the voltage indicated by each of these devices.

  Find when the triggering angle is greater than 140 degrees

The average voltage across the load when the triggering angle is 140 degrees. Keep in mind that the conduction is incomplete when the triggering angle is greater than 140 degrees.

  What is the net profit for each digital thermometer sold

Consider the financial aspects of the digital thermometer project. The project cost is estimated at $10,000. The total manufacturing cost of the digital thermometer, as called for in the specifications, total $150(that is, $95 parts

  Define the voltage and current in the laplace domain

The voltage and current in the Laplace domain for a certain system is given by V (s) = 1/12 1/s^2 +3, I(s) = s/s^2+3. Is this system best described as resistive, capacitive, or inductive?

  Find what is the maximum possible data rate

A communications channel has a bandwidth of 2,000 Hz and a signal-to noise-ratio (SNR) of 20 dB. What is the maximum possible data rate

  Write and test a c program that outputs a waveform

Write and test a C program that outputs a waveform that switches from 10.0 kHz with a 50% duty cycle to 25.0 kHz with a 5% duty cycle every 5 seconds. Your code design must be modular - initializations and program operations are to be performed

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd