At what frequency or frequencies does the maximum gain occur

Assignment Help Electrical Engineering
Reference no: EM13250397

If a system has a unit-impulse-response of h(t) = 100t * e^(-20t) u(t) , where u(t) is the standard unit step function, then determine the transfer function H(f) for the system. What type of filter is this system (high-pass, low-pass, band-pass, or band-reject)? What is the highest gain (or magnitude of the transfer function)? At what frequency or frequencies does this maximum gain occur? At what frequency or frequencies is the magnitude of the transfer function 3 dB lower than its maximum magnitude?

Reference no: EM13250397

Questions Cloud

Risk tolerance and asset allocation : Write a review of the article. Use finance theory to explain and critique the key points that the authors are trying to communicate - Risk tolerance and asset allocation for investors nearing retirement
Define a chemical reaction for the process : write a chemical reaction for this process. If a sample of the supernatant from the reaction above were used as part of a half cell along with a zinc electrode and the other half-cell was a standard hydrogen electrode, what is the potential of the..
Calculate the labor-force participation rate : Suppose that the country of Bigu has a population of 127 million, of which 83 million are in working- age population. of those, 2.5 million are not in the labor force and 52 million are employed.
What is the magnitude of its linear acceleration : A yo-yo has a rotational inertia of 970 g·cm2 and a mass of 104 g. Its axle radius is 3.15 mm, What is the magnitude of its linear acceleration
At what frequency or frequencies does the maximum gain occur : If a system has a unit-impulse-response of h(t) = 100t * e^(-20t) u(t) , where u(t) is the standard unit step function, then determine the transfer function H(f) for the system. What type of filter is this system (high-pass, low-pass, band-pass, ..
Is the merger likely to be approved : is the merger likely to be approved? Why or why not? In your answer, be as quantitative as possible
Explain what is the ph solution of aqueous acetic acid : What is the pH of a 0.15 M solution of aqueous Acetic Acid. The Ka of acetic acid is equal to 1.7 x 10^-5
Explain a solution has a hydronium ion concentration : A solution has a hydronium ion concentration of [H3O+] = 5.3 x 10^-4 Determine the pH of this solution.
What fraction of the total kinetic energy of the car : A 878 kg car has four 11.8 kg wheels. When the car is moving, what fraction of the total kinetic energy of the car is due to rotation of the wheels about their axles

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Find the total power of the noise passed through the system

Gaussian White Noise with Power Spectral Density Sn(f) = 10 mu W/Hz is applied to a linear system with impulse response h(t) = exp(- |5t|)u(t)cos(2 phi 10t) Write the equation for the Power Spectral Density of the noise passed through the system

  Calculate current in incoming and outgoing transmission line

three single-phase transformers rated at 250kVa, 7200V/600, 50Hz, are connected in wye-delta on a 12470V, 3 phase line, if the load is 450kVA, calculate the current in the incoming and outgoing transmission lines and in the primary and secondary w..

  Estimate resistivity of pure silicon in ohm-cm at room temp

Assuming dopant atoms are uniformly distributed in a silicon crystal, how far apart are these atoms when the doping concentration is a) 10l5 cm-3, b) 1018 cm-3, c) 5times1020 cm-3. Estimate the resistivity of pure silicon in Ohm-cm

  Design a low-pass filter that attenuates the noise

A measurement signal has a frequency less than 1 kHz, but there is unwanted noise at about 1 MHz. Design a low-pass filter that attenuates the noise to 1%. What is the effect on the measurement signal at its maximum of 1 kHz

  Why the process is considered to be polytropic

Calculate the amount of work done if the process is considered to be polytropic. Assume the temperature to be 273K and the value of k for the process to be 1.4. All losses are neglected.

  Determine how many overflows will occur

The input capture option on the HCS12 is used to measure the period of a 100 Hz signal. With an E-clock of 24 MHz and no scaling, how many overflows will occur Assume the free-running timer starts at 0x0000.

  Define binary pcm system

The signal m(t)=6sin(2*pi*t) volts is transmitted using 4-bit binary PCM system. The quantizer is of the midriser type, with a step size of 1v

  Design the combinational logic circuit for an elevator

Design the combinational logic circuit for an elevator controller such that the option to go up or down by only one floor is disabled. Assume that the building the elevator is in has 4 floors. Your inputs are the current floor and the next request..

  Show the relative uncertainty in volumetric flowrate

Water is flowing out of a tube at a near constant volumetric flowrate, V .If a graduated cylinder is used to collect a certain volume, v , of the water, and a timer is used to measure the time, t, required to collect the volume of water, the volum..

  Find the percentage regulation when supplying full load

A 10kVA, 200/400V 50Hz single-phase transformer gave the following test results. O/C test: 200V, 1.3A, 120W, on l.v. side. S/C test: 22V, 30A, 200W on h.v. side. (a) Calculate the magnetizing current and the component corresponding to core loss at ..

  What is the indicated temperature at the times

A temperature sensor has a static transfer function of 0.15 mV/C° and a time constant of 3.3 s. If a step change of 22° to 50° C is applied at t=0, find the output voltage at 0.5 s from t=0s to t=10s. What is the indicated temperature at these tim..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd