At the minimum volume reached calculate the shrinkage limit

Assignment Help Civil Engineering
Reference no: EM13550265

1.At the minimum volume reached during shrinkage, a specimen of soil has a void ratio of 0.87. if Gs = 2.72, calculate the shrinkage limit

2.Using an order-of-magnitude analysis, estimate the number of 4ft x 8ft plywood sheets rewuired for the floor, roof, and exterior sheathing of a 600 ft squared house.

3.CO2 contained in a piston-cylinder device is compressed from initial state of p1 = 100 kPa, V1 = 0.004 m3, to a final pressure of p2 = 500 kPa. During the process, the pressure and volume are related by pV1.22 = constant. Calculate the work.

4.The suspended load exerts a force F = 600 lb at A and bar OA weighs 200 lb. Assume that the bar’s weight acts at its midpoint. Determine the tensions in the cables and the reactions at the ball and socket support O. Draw complete FBD(s) for full credit.

Reference no: EM13550265

Questions Cloud

Determine the average impulsive force developed : The 180-lb iron worker is secured by a fall-arrest system consisting of a harness and lanyard AB, which is fixed to the beam. If the lanyard has a slack of 4 ft, determine the average impulsive force developed in the lanyard if he happens to fall 4 f..
Determine the total bond interest expense : Determine the total bond interest expense to be recognized over the bonds life and prepare a straight-line amortization table like the one in Exhibit 14.7 for the bonds' first two years.
Find the increase in thermal energy of the bed and floor : A collie drags its bed box across a floor by applying a horizontal force of 3.1 N. find the increase in thermal energy of the bed and floor
Obtain the average frictional force that acts on slidingbear : A 49 kg bear slides, from rest, 10 m down a lodgepole pine tree, moving with a speed of 3.8 m/s just before hitting the ground. What is the average frictional force that acts on the sliding bear
At the minimum volume reached calculate the shrinkage limit : The suspended load exerts a force F = 600 lb at A and bar OA weighs 200 lb. Assume that the bar’s weight acts at its midpoint. Determine the tensions in the cables and the reactions at the ball and socket support O. Draw complete FBD(s) for full cred..
Calculate what is the mass of the sled : A boy of mass m runs with a speed v and jumps onto a sled on an icy pond. The sled was at rest before the boy jumped onto it. After the jump, What is the mass of the sled
How much will operating income increase or decrease : If Zion decides to purchase the component from Bryce, by how much will operating income increase or decrease? Which alternative is better?
Find the angle between two first-order diffraction minima : Diffraction also occurs with sound waves. Consider 1400-Hz sound waves diffracted by a door that is 93 cm wide. What is the angle between the two first-order diffraction minima
Determine how many radians should he walk per day : In Europe, a large circular walking track with a diameter of 0.900 km is marked in angular distances in radians. How many radians should he walk per day to maintain his daily routine

Reviews

Write a Review

Civil Engineering Questions & Answers

  What will be the coefficient of permeablity of sand

A loose uniform sand with rounded grains has effective grain size of 0.05 cm. What will be the Coefficient of permeablity of sand

  Estimate the annual et losses in inches for the area

For a drainage area of 5,187mil^2 mean annual runoff is determined to be 3,708ft^3/s and the annual averge rainfall is 35.5 inches. Estimate the annual ET losses in inches for the area. ( 1 mile = 5,280ft)

  Develop preliminary wbs for small one-story to be construct

The exterior and interior walls are of concrete block. The roof is constructed of bar joists covered with a steel roof deck, rigid insulation, and built-up roofing.

  What are the predominant types of bond in each category

what are the three meterials based on the predominant types of bond and what are the predominant types of bond in each category

  Determine how many units of each product company should make

The number of hours on each machine required to produce a product is given in the following table, along with the number of hours available per week on each type of machine. Assume that the company can sell everything it produces.

  Find the minimum length of runway required for the landing

Find the minimum length of runway required for the landing (I found to be 300ft). Find the position on the runway where the speed is 50ft/s and the time it takes for the speed to reach 50ft/s

  Determine what will be carbondioxide level 10 years later

Assume to just using coal as an electric energy source. Take efficency as %50 for average power plant.If the carbondioxide level is 400 ppm by volume now, what will be the carbondioxide level 10 years later

  Evaluate company performance in relation to GRI standards

Evaluate company performance in relation to GRI standards and comment on Stigler's theory.

  Determine the velocity and position of point a at time t

The acceleration of point A is defined by the relation a = -1.08sin kt - 1.44 cos kt, where a and t are expressed in m/s^2 and seconds, respectively, and k = 3 rad/s. knowing that x = 0.16 m and v = 0.36 m/s when t = 0

  Determine the tensions in the cables and the reactions at a

The force F is acting on the boom ABC at C points in the direction of the unit vector 0.7071i-0.7071j and its magnitude is 10kN. The boom is supported by a ball and socket at A and cables BD and BE.

  Determine how much money the home owner would have saved

A house that was heated by electric resistance heaters consumed 1200 kWh of electric energy in a winter month. If this house were heated by a heat pump that has an average COP of 2.4, determine how much money the home owner would have saved that mont..

  Calculate the total weight

Identical bricks 0.1m wide, and weighting 2kg are placed on a plate (assume the plate has neligible weight). Calculate the total weight (and force F required to balance the plate). How far from x=0 should F be placed so that the plate will not tip..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd