At the end of the isothermal expansion the pressure is 600

Assignment Help Mechanical Engineering
Reference no: EM13640092

Two kilograms of air within a piston-cylinder assembly execute an ideal Carnot power cycle within maximum and minimum temperatures of 750 K and 300 k, respectively. The heat transfer to the air during the isothermal expansion is 60 kJ. At the end of the isothermal expansion, the pressure is 600 kPa. Assuming the ideal gas model for the air (cv, cp, and specific heat ratio k, are constants and: kair=1.4, cv,air=0.717J/g.K, Mair =28.97g/mol, ),

(a) Sketch the cycle on a p-V diagram;
(b) Determine the thermal efficiency of the cycle;
(c) Determine the pressure and volume at the beginning of the isothermal expansion;
(d) Determine the work and heat transfer for each of the four processes.

Reference no: EM13640092

Questions Cloud

A population has mean 20 a simple random sample of size 100 : a population has mean 20. a simple random sample of size 100 is selected from this population. what is the mean of the
The enthalpies of the gas at entry asnd exit are 950 kjkg : a stream of gases at 7.5 bar 750 ordmc and 140 ms enters the turbine of a jet engine. the stream comes out of the
A population has mean 20 a simple random sample of size 100 : a population has mean 20. a simple random sample of size 100 is selected from this population. what is the mean of the
A student used a dcp solution standardized to 994x10-4m to : a student used a dcp solution standardized to 9.94x10-4m to analyze a sample of extract from 3.50g of solid food. the
At the end of the isothermal expansion the pressure is 600 : two kilograms of air within a piston-cylinder assembly execute an ideal carnot power cycle within maximum and minimum
You take 31789 g of a substance and place it into 1000 g : you take 3.1789 g of a substance and place it into 100.0 g of benzene. the boiling point of this solution is found to
Radiation from sun is absorbed at the plate surface at the : the flat plate 1 m in length and 1 m in width is placed parallel to the air stream at 27ordmc 1 atm. the air free
Find the critical speed when the trailer is traveling over : the springs of an automobile trailer are compressed 10.6 cm under its weight. find the critical speed when the trailer
A set of 200 independent patients take antiacid medication : a set of 200 independent patients take antiacid medication at the start of symptoms and 80 experience moderate to

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd