At a point on the free surface of a machine part the

Assignment Help Mechanical Engineering
Reference no: EM13627757

At a point on the free surface of a machine part, the strains are Ex=+1200 mu, Ey=+300mu, Yxy=+700 mu. Use Mohr's circle to determine:

a. What are the in plane principle strains and show on a sketch their orientation to the x-y axis.

b. What is the out of plane strain?

c. What is the maxium shearing strain?

d. If a strain gauge was also mounted as shown in the figure below, what reading would be measured?

e. What are the principal stresses? Assume that E= 200 GPA and v=0.3.

Reference no: EM13627757

Questions Cloud

A system consisting of 3 lb of water vapor in a piston- : a system consisting of 3 lb of water vapor in a piston- cylinder assembly initially at 350degf and a volume of 71.7 ft3
In designing an experiment involving a treatment applied : in designing an experiment involving a treatment applied to 5 test subjects researchers plan to use a simple random
If an oscillation of a mass on a spring has 16 times the : if an oscillation of a mass on a spring has 16 times the energy of another oscillation of the same mass on the same
A pitot-static tube is used to measure the airspeed of an : a pitot-static tube is used to measure the airspeed of an airplane. the pitot tube is connected to a pressure sensing
At a point on the free surface of a machine part the : at a point on the free surface of a machine part the strains are ex1200 mu ey300mu yxy700 mu. use mohrs circle to
In designing an experiment involving a treatment applied : in designing an experiment involving a treatment applied to 5 test subjects researchers plan to use a simple random
A gas turbine unit has compressor inlet conditions of 100 : a gas turbine unit has compressor inlet conditions of 100 kpa and 310 k. the compressor discharge pressure is 700 kpa
A uniformhorizontal string has a mass of 0030 kg and a : a uniformhorizontal string has a mass of 0.030 kg and a length of 6.00 m. this string is attached toa wall at one end.
Most of the live characters at an amusement park have : a survey found that womens heights are normally distributed with mean 62.3 in. and standard deiation 2.3 in. the survey

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  If the spar has a cross sectional area of 10 mm x 20 mm how

a 2014-t6 aluminum spar in an airframe is expected to support an alternating load ranging between 32 kn and -32 kn at a

  What work is done by the gun on the slug to put this number

in the movie eraser the bad guys had a gun that would shoot a 5 g aluminum slug at one quarter the speed of light. lets

  The compressor is cooled by the ambient air at 15 degc at

air enters a compressor at ambient conditions of 100kpa and 17 degc with a low velocity and exits at 1mpa 327 degc and

  If the volume of the air in the tank is 2 cubic meters find

an insulated rigid-wall tank contains air at 20 c and 2 bar. a paddle wheel located in the tank does work on the air in

  Determine the horizontal line along

Determine (a) the horizontal line along which the shearing stress is a maximum, (b) the constant k in the following expression for the maximum shearing stress.

  Draw a diagram of the system and state necessary

design a stationary steam power plant operating on an ideal closed loop rankine cycle that can deliver 85 mw of net

  If the initial value of n is 1 millionl what values of k

suppose the rate of growth of a bacterial population n cellsliter is described by dndt kn -1000. the terms represent

  A solid object of aisi 302 steel at a temperature of 850c

a solid object of aisi 302 steel at a temperature of 850?c is quenched in mineral oil at a temperature of 25?c. the oil

  Explain a car and a high speed trian at constant speeds

A car and a high -speed trian at constant speeds. three seconds after the train passes under the highway bridge the car crosses the bridge.

  Determine the design stress for bolts in a cylinder cover

determine the design stress for bolts in a cylinder cover where the load is fluctuating due to gasnbsppressure. the

  Find the desired radius and mass of the absorber

Find the desired radius and mass of the absorber if the absorber is to not exceed an angular deflection amplitude of 30 degrees when the engine is running at 750 rpm.

  A load of 500 pounds is placed on a cylinder of 1040

a load of 500 pounds is placed on a cylinder of 1040 carbon steel with a 2 inch radius. calculate the stress in

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd