At 20 degrees c what is the minimum diameter of the cu wire

Assignment Help Mechanical Engineering
Reference no: EM13641540

1. An array of solar panels on a residential roof produces (at full sun) 7.2 kW of dc power, &voltage of 600V a 40-ft Cu wire connects the panel from the roof to the inverter in the basement. At To= 20 degrees C, the electrical resistivity of copper is po= 1.67E-6 (omega*cm), and at higher temperatures, the resistivity of copper is p=po[a(T-To) with a=.0039/degrees C.

a. at 20 degrees c, what is the minimum diameter of the Cu wire, such that no more than 1% of the produced power is "consumed" by the resistance of the wire?

b. By what percentage does the resistivity of the Cu wire increase if temperature is raised from 20 degrees to 40 degrees C on a summer day?

2. The solar cells are made of silicon, with a band gap of 1.1 eV. The solar spectrum has wavelengths ranging from approximately 200 nm to 10 um. Some of the light is is absorbed in the Si while the rest of the light is traveling through the solar cell without being absorbed. Which part of the spectrum is absorbed in the silicon? provide the range of wavelengths

3. Diamond is considered as a possible element to make semiconducting devices; despite that the band gap of diamond is rather high. Looking at the periodic table, which element would you add to diamond to make it p-doped? why?

Reference no: EM13641540

Questions Cloud

Assume that the density of blood is 105 gcm3 and that the : a spherical bubble of air is introduced into a vein in the ankle. the diameter of this bubble is 0.5 mm. as the bubble
The pipe has a surface temperature that is maintained at : oil passes through a 5-m long 25-cm diameter circular pipe with a mass flow rate of 75 kgh. the oil enters the pipe at
Assume all the energy in the doughnut can be converted to : a doughnut contains about 335 calories. note these are food calories. after eating this doughnut you decide to
A solution containing 10 mmol of co3-- and 50 mmol of : a solution containing 10 mmol of co3-- and 5.0 mmol of hco3- is titrated with 1.0 m hcl. what total volume of hcl must
At 20 degrees c what is the minimum diameter of the cu wire : 1. an array of solar panels on a residential roof produces at full sun 7.2 kw of dc power ampvoltage of 600v a 40-ft cu
What do the terms activating deactivating ortho : what do the terms activating deactivating ortho para-directing and meta-directing mean. how do these relate to aniline
Find ex where x is the outcome when one rolls a six-sided : find ex where x is the outcome when one rolls a six-sided balanced die.find the mgf of x. also using the mgf of x
A baseball leaves a pitchers hand horizontally at a speed : a baseball leaves a pitchers hand horizontally at a speed of 160 kmh. the distance to the batter is 18.3 m. neglect air
Fluorine-18 undergoes positron emission with a half-life : fluorine-18 undergoes positron emission with a half-life of 1.1x102 minutes. if a patient is given a 248mg dose for a

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd