Assuming this carbon has a bulk density of 25 lbft3 and if

Assignment Help Mechanical Engineering
Reference no: EM13631154

A polluted air stream flowing at 12,000 acfm at 90 °F and 1 atm has a concentration of 500 ppm of ethylbenzene (C8H10). Pilot plant studies of adsorption processes indicate that 11 lb (net) of ethylbenzene will be adsorbed per 100 lb of carbon during normal everyday operations.

a. Calculate the minimum amount of carbon needed in one bed for a two hour run time. Give your answer in pounds.

b. Assuming this carbon has a bulk density of 25 lb/ft3, and if the bed must be at least 1.5 feet deep, calculate the superficial gas velocity in a bed that contains this amount of carbon. Give your answers in ft/min.

c. Comment on this superficial gas velocity. If it is too high or too low, determine what you would do to correct it. Be specific and give dimensions of the re-sized bed. How does the run time change?

 

Reference no: EM13631154

Questions Cloud

What is the amount of recycle gas in mol per 100 kg of p if : to save energy stack gas from a furnace is used to dry rice. a gas containing 4.73 mol water is fed into the dryer as
A sample with a temperature of 10651 degrees c is dropped : a sample with a temperature of 106.51 degrees c is dropped into an insulated cup containing water whose mass is the
If a refrigeration cycle is operating between the same : a power cycle operates between 100 degrees c and 25 degrees c. if the heat transfer rate from high temperature
What was the average dose rate 35 billion years ago state : todays terrestrial background radiation is about 50 mremyear mainly due to the uranium and thorium decay chains and
Assuming this carbon has a bulk density of 25 lbft3 and if : a polluted air stream flowing at 12000 acfm at 90 degf and 1 atm has a concentration of 500 ppm of ethylbenzene c8h10.
Calculate and compare the electron densities of a piece of : calculate and compare the electron densities of a piece of aluminum 1 cm thick and a piece of iron of the same density
A light truck weighs 3100 lb and is rated at 30 miles per : a light truck weighs 3100 lb and is rated at 30 miles per gallon for a 60 mph highway driving on level ground. how much
A neutron passes two points 10 meter apart in 10 : a neutron passes two points 1.0 meter apart in 1.0 microsecond. calculate the neutrons energy in units of both joules j
A particular material has a dielectric constant of 17 and a : a particular material has a dielectric constant of 1.7 and a dielectric strength of 14.0 mvm. if this material is used

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd