Assuming one-dimensional heat transfer and disregarding

Assignment Help Mechanical Engineering
Reference no: EM13640406

A 4-m high and 6-m wide wall consists of a long 18-cm x 30-cm cross section of horizontal bricks (k = 0.72 W/m ·°C) separated by 3-cm-thick plaster layers (k = 0.22 W/m ·°C). There are also 2-cm-thick plaster layers on each side of the wall, and a 2-cm-thick rigid foam (k = 0.026 W/m ·°C) on the inner side of the wall. The indoor and outdoor temperatures are 22 °C and -4 °C, and the convection heat transfer coefficients on the inner and outer sides are 10 W/m2 ·°C and 20 W/m2 ·°C, respectively. Assuming one-dimensional heat transfer and disregarding radiation, determine the rate of heat transfer through the wall.

Reference no: EM13640406

Questions Cloud

Steam flows steadily through a nozzle the steam enters the : steam flows steadily through a nozzle. the steam enters the nozzle at p15mpa and t1350 c the steam leaves the nozzle at
Suppose that annual precipitation in a midwestern city : suppose that annual precipitation in a midwestern city follows a normal distribution with a mean of 25 inches and a
A microscope can resolve as two distinct objects of : a microscope can resolve as two distinct objects of features that are no closer than the wavelength of the light or
If z is a standard normal random variable then what is : if z is a standard normal random variable then what is pr-2.61 lt z lt 0.23? use four decimal places of
Assuming one-dimensional heat transfer and disregarding : a 4-m high and 6-m wide wall consists of a long 18-cm x 30-cm cross section of horizontal bricks k 0.72 wm middotdegc
If z is a standard normal random variable then what is : if z is a standard normal random variable then what is przgt-2.43? use four decimal places of accuracy.can you also
For each plot use a range x or y okm to 1 km find the : the flow field for and atmospheric flow is given byv -my2pi imx2pi jwhere m1 s -1 and the x and y coordinates are the
Bromothymol blue ka 16 x 10-7 is yellow in its protonated : bromothymol blue ka 1.6 x 10-7 is yellow in its protonated form hx and blue in its ionized form x-. at what ph will
Regression analysis is used when the independent variable : regression analysis is used when the independent variable is nominal or ordinal in nature.a. trueb.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine a the natural frequency in rpm of the platform if

a platform of weight 200 lb supported by two springs each of constant k 250 lbin. is subjected to a periodic force of

  Determine the stress in the wires

a 1.5 ton crate is hoisted by three steel wires. each wire is 1/4 in. in diameter and each carries one-third of the load. determine the stress in the wires.

  Explain midrange and amplitude components

Midrange and amplitude components, A shaft is subjected to a completely reversed bending stress such that Xmax=40kpsi and Xmin=-40kpsi

  How much energy must be added as heat to bring the water to

three kg of water in a piston-cylinder apparatus is initially in the saturated liquid state at 0.6 mpa. energy is added

  Determine the value of heat flux that must be supplied by

the air inside a chamber at 54 c is heated convectively with heat transfer coefficient of 35 wm2k by a 0.29-m thick

  Estimate the maximum elongation and maximum tensile stress

a 5-ton elevator is supported by a standard steel cable of 25 in2 cross section and an effective modulus of elasticity

  Determine expressions for attractive and repulsive energies

determine the expressions for attractive and repulsive energies, EA and ER as a functions of r where r is in nm and E is in eV.

  Relative a reference frame the recorded motion of p for the

a ship tracks an unmanned vehicle p in the water. relative a reference frame the recorded motion of p for the first t

  A 1000 n force is applied in the beam length x direction a

a cantilevered bar is 500 mm long with square cross section 25mm x 25 mm. three perpendicular forces are applied to its

  Clculate a stroke length cm b average piston speed msec c

a pickup truck has a five liter four stroke cycle v6 si engine operating at 2400 rpm. the compression ratio rc10.21 the

  A tensile force of 1000 n 225 lbf produces an elastic

consider a cylindrical specimen of some hypothetical metal alloy that has a diameter of 8.0 mm 0.31 in.. a tensile

  Design a v-beltchaon drive which limits the top speed to

a mini motor bike for chidren is powered by a 4 hp single cylinder gasoline engine governed to run at a maximum of 2250

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd