Assuming air to be an ideal gas

Assignment Help Mechanical Engineering
Reference no: EM13704744

Assuming air to be an ideal gas, what would be the mass of air in a classroom of size 20 ft x 15 ft x 9 ft assuming the pressure inside the classroom is 1 atm and the classroom is at a constant temperature of 20^o C . Would the mass of gas inside the class room change much if the room is filled with N_2? Why?

Reference no: EM13704744

Questions Cloud

Large hydraulic cylinder with a piston diameter : You have a large hydraulic cylinder with a piston diameter of 8.00 inches. The rod of the cylinder is extended 48 inches. The pressure inside the cylinder at time, t = 0.00 sec is 1,000 psig. There is a 10 foot long hose connected to the hydraulic cy..
After the initial cleanup effort at three mile island : After the initial cleanup effort at Three Mile Island, approximately 400,000 gallons of radioactive water remained in the basement of the containment building of the Three Mile Island Unit 2 nuclear plant. The principal sources of this radioactivity ..
The change in flow availability for compressor and turbine : An irreversible gas-turbine power plant has a compressor with an inlet state of 1 bar and 22°C and an outlet state of 4 bars and 470 K. The turbine has an inlet state of 4 bars and 1200 K and an exhaust state of 1 bar and 900 K. The environment is at..
Calculate the work for the entire process : A frictionless piston-cylinder contains 3.0 kg of H2O and is initially at 300 kPa. The initial volume is 1.0 m3. The water is heated until the temperature is 300 C. If the volume within the system reaches 1.5 m3, the piston hits a set of stops and is..
Assuming air to be an ideal gas : Assuming air to be an ideal gas, what would be the mass of air in a classroom of size 20 ft x 15 ft x 9 ft assuming the pressure inside the classroom is 1 atm and the classroom is at a constant temperature of 20^o C . Would the mass of gas inside the..
Advise jim as to his legal position : Advise Jim as to his legal position. Does a contract exist - case law and the relevant sections of any applicable legislation.
Developed the law of exponents for multiplication : Developed the law of exponents for multiplication, compare and contrast the law of exponents for division and multiplication specifically mention what you know about the base and exponent of each one
Found to involve 3.5 minutes of machine time per cycle : A worker-machine operation was found to involve 3.5 minutes of machine time per cycle in the course of 40 cycles of stopwatch study. The worker's time averaged 2.7 minutes per cycle, and the worker was given a rating of 120 percent
Preparing the financial statement and financial entries : What is adjusting entries and why is Delay for preparing the financial statement and financial entries. Define criticism

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd