Assume the entire mass within the house

Assignment Help Mechanical Engineering
Reference no: EM13712624

Assume the entire mass within the house (air, furniture, etc) is equal to 1,670 kg of air.

A heat pump with a COP of 3.0 is used to heat an air-tight house. When running, the heat pump consumes 5 kW of power. If the temperature in the house is 5 degrees C when the heat pump is turned on, how long will it take for the heat pump to raise the temperature of the house to 19 degrees C?

Reference no: EM13712624

Questions Cloud

Explain how would steel strength be affected : We are concerned about carbon content in steel. It has a direct effect on the yield and tensile strength of what is formed in what is called a hot rolled condition directly from the steel production facility. 1010 steel has a yield strength of 180MPa..
What are the critical contemporary issues : What are the critical contemporary issues related to consumer buying behavior and perceptions?
The diameter of largest solid sphere for lumped behaviour : For plain carbon steel, with properties at 300K in the Appendix and convection (h=50 W/m^2 K) to air at 500K. the diameter of largest solid sphere for lumped behaviour (2 part- show equivalent length is D/6 and that D for Bi
Performing both an energy balance and an entropy analysis : By performing both an energy balance and an entropy analysis, calculate the change in entropy when 1 mole of saturated ethanol vapor condenses at its normal boiling point.
Assume the entire mass within the house : A heat pump with a COP of 3.0 is used to heat an air-tight house. When running, the heat pump consumes 5 kW of power. If the temperature in the house is 5 degrees C when the heat pump is turned on, how long will it take for the heat pump to raise the..
Membrane made of an isotropic material whose elastic modulus : There is a membrane made of an isotropic material whose elastic modulus and Poisson's ratio is E and v, respectively. When this membrane is elongated along x-direction with no lateral deformation in y-direction, the apparent elastic modulus (E') dete..
Find the indicial equation and its roots : Find the indicial equation and its roots. Find the recurrence relation. Use the recurrence relation to find the first three terms of the power series solution corresponding to one root of the indicial equation
Silicon rubber drain hose for surgical procedure : Silicon rubber has a Poisson’s ratio of 0.4. Consider a silicon rubber drain hose for a surgical procedure; the hose has an outer diameter of 4 mm and a wall thickness of 0.5 mm. How much does the lumen (interior space) of the catheter constrict if t..
Calculate the mole fraction of methane in the fuel : A fuel gas containing methane and ethane is burned with air in furnace, producing a stack gas at 300C and 105kPa (absolute). The stack gas contains C02 at a partial pressure of 80 mm Hg and no CO,O2, methane or ethane. Calculate the mole fraction of ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A cutting tool on a lathe applies a tangential force

A cutting tool on a lathe applies a tangential force of 3.5 kN when it is machining a bar 150 mm in diameter. If the lath is turning at 100 rpm, what power is being supplied to the bar?

  Find the value of heat transfer coefficient that will

a 2.5 cm thick layer of insulation k 1.5 wm oc is applied to a plane surface so that the inner surface of the

  If upon initial null balance r3 is 1275 ohms and if when r2

a simple wheatstone bridge as shown in fig. 7.10 is used to determine accurately the value of an unknown resistance r1

  For the compressor the isentropic efficiency is 92 and for

air enters the compressor of a regenerative air-standard brayton cycle with a volumetric flow rate of 60 m3s at 0.8 bar

  A 120 lbf 534 n skydiver is free-falling at an altitude of

a 120 lbf 534 n skydiver is free-falling at an altitude of 6500 ft 1980 m. estimate the terminal velocity in mph for

  Oil pump is being driven by the shaft of an electric motor

An oil pump is being driven by the shaft of an electric motor. The motor consumes 44 kW of power while pumping the oil – having a density of 0.860 g/cm3 – at a rate of 0.1 m3/s.

  What is the difference between the specific internal energy

What is the difference between the specific internal energy of a mixture of saturated water liquid and vapor with a quality of 10 percent (x = 0.1) at 200 degrees C and 100 degrees C.

  Calculate the mass of vapor at the beginning and end of the

a closed and rigid tank with 1.5 m3 volume initially contains saturated vapor refrigerant 134a at 50deg c. the system

  Two kg of saturated liquid water at 1 bar is compressed to

two kg of saturated liquid water at 1 bar is compressed to 25 bar and 100degc in a water pump. determine the change in

  How much heat must be transferred from the energy-source to

an energy-source at 1000 k transfers heat to a completely reversible heat engine. this engine transfers heat to a sink

  A 25-hp 240-v 778-a shunt motor has an armature resstence

a 25-hp 240-v 77.8-a shunt motor has an armature resstence of 0.083 ohms and a field-circuit resistance of 125 ohms.

  Charge of melting and casting for making alloy

Assuming that you are a process engineer in charge of melting and casting for making an alloy that consists of 40 at% Ag and 60 at% Ni. Calculate how many grams of Ag and Ni you need to weigh to make a 400-gram solder alloy with such a composition. G..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd