Assume the cost of electricity is 89 cents per kwh

Assignment Help Mechanical Engineering
Reference no: EM13613406

An electrically driven pump operating at steady state is used to draw water from a pond. At the pump inlet the pressure is 1 bar, and the mass flow rate is 50 kg/s. The pump outlet pressure is 5 bars. To a close approximation the pump performance is adiabatic, and changes in kinetic and potential energy are negligible. Assume the cost of electricity is 8.9 cents per kW.h. Determine the hourly cost of running the pump if the pump efficiency is 80%.

Reference no: EM13613406

Questions Cloud

In the united states a full-time employee works an average : in the united states a full-time employee works an average of 40 hours a week with a standard deviation of 2.5 hours
Joes automobile which was used only for business purposes : joes automobile which was used only for business purposes was damaged in an accident. at the date of the accident the
The power input to the steam is known to be 500 w determine : a refrigeration system is designed to operate between temperture limits of -10 c and 25 c. the power input to the steam
Suppose a company has 5 different capital budgeting : suppose a company has 5 different capital budgeting projects from which to choose but has constrained funds and cannot
Assume the cost of electricity is 89 cents per kwh : an electrically driven pump operating at steady state is used to draw water from a pond. at the pump inlet the pressure
A what potential difference between the two wires would : a person can be killed if a current as small as 50 ma passes near the heart. an electrician is working on a humid day
A new muscle relaxant is available researchers from the : a new muscle relaxant is available. researchers from the firm developing the relaxant have done studies that indicate
The probability distribution of the discrete random : the probability distribution of the discrete random variablenbspxnbspis given by the following
Find the acceleration relative to the ground of the highest : the acceleration of a particle in a fixed coordinate system in terms of its position in a translating and rotating

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  In a design test of penetration resistance a 12-gram bullet

in a design test of penetration resistance a 12-gram bullet is fired through a 400-mm stack of fibrous plates with an

  Draw a schematic of the turbine as a control volume label

steam having pressure 4.0 mpa and temperature of 880 k enters the turbine installed in a power plant at the rate 500

  The belt connecting these pulleys is represented by two

a pulley 250 mm in diameter drives a second pulley 1000 mm in diameter by means of a belt. the moment of inertia of the

  Calculate the overall efficiency the heat rate mw and the

calculate the overall efficiency the heat rate mw and the total fuel rate kgs of a combined-cycle power plant 1 if no

  Determine the moments of inertia

two 20mm steel plates are welded to a rolled S section as shown. Determine the moments of inertia and the radii of gyration of the combined section with respect to the centroidal x and y axes.

  Draw the front view - third angle projection

Partial Auxiliary View showing the details of the inclined face - supply dimensions for the inclined face only. Select a suitable scale to make the drawing fit on an A3 drawing sheet.

  Question 1 bending about two axesthe load p 2 kn is

question 1 bending about two axesthe load p 2 kn is applied to the end of rectangular section cantilever beam shown

  Measure the length of the beam what is the torque

measure the length of the beam. what is the torque calibration coefficient? 7 explain any anomalies - differences from

  Looking at the different convergence methods which

looking at the different convergence methods which convergence method polynomial order andor meshing would you

  Determine the final pressure 8 b was the compression

the adjoining figure illustrates a piston-cylinder arrangement. this cylinder contains helium at 21oc and 1.379 mpa.

  Consider a supersonic wind tunnel with test section mach

consider a supersonic wind tunnel with test section mach number of 2 and fixed geometry diffuser designed to operate

  Calculate the angular separation between the first order

Calculate the angular separation between the first order minima on either side of the central maxima when the slit has a width of 6x10-4 cm & light illuminating it has a wavelength of 6000A0?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd