Assume that a person is on a roof and that the structure

Assignment Help Mechanical Engineering
Reference no: EM13629982

Assume that a person is on a roof and that the structure has a circular cross section. If the interface is frictionless and at pheta= 0 rad pheta dot = 0.5 rad/s, at what angle will contact be lost? (Hint: You will need to find the equation of motion in terms of pheta and determine where the normal force goes to zero.) r = 20 m.

Reference no: EM13629982

Questions Cloud

Air contained in a piston-cylinder assembly is initially at : air contained in a piston-cylinder assembly is initially at 350 k 150 kpa and a volume of 0.15 l. as the cylinder is
Let x the time between two successive arrivals at the : let x the time between two successive arrivals at the drive-up window of a local bank. if x has an exponential
Air flows steadily through an insulated 5 cm constant : air flows steadily through an insulated 5 cm constant diameter duct fitted with a fan. the air enters the suction side
Calculate the final temperature when 1600g of water at 35oc : calculate the final temperature when 1600g of water at 35oc in a 125g cu calorimeter is mixed with 128g of steam
Assume that a person is on a roof and that the structure : assume that a person is on a roof and that the structure has a circular cross section. if the interface is frictionless
Air in a piston-cylinder assembly undergoes a process from : air in a piston-cylinder assembly undergoes a process from state 1 where t1 300 k p1 100 kpa to state 2 where t2500 k
The rockwell hardness of a metal is determined by : the rockwell hardness of a metal is determined by impressing a hardened point into the surface of the metal and then
Car a is speeding in the positive x direction and is about : car a is speeding in the positive x direction and is about to run through a red light and collide with car b heading
For an unpolarized electric field ie the electric field has : for an unpolarized electric field i.e. the electric field has polarization components both parallel and perpendicular

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Providing domestic hot water to a household typically

providing domestic hot water to a household typically requires 107 kj of energy per year. a typical electric water

  Heat is then slowly removed from the nitrogen during a

consider nitrogen gas contained in a piston-cylinder device. the cylinder diameter is 150 mm. at the initial state the

  A particle moves along the curve yx2 - 4m with a constant

a particle moves along the curve yx2 - 4m with a constant speed of 5 ms. determine the point on the curve where the

  The average radius of the wheel is 183 m and the jet

a pelton wheel is used to produce hydroelectric power. the average radius of the wheel is 1.83 m and the jet velocity

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Calculate the max deflection in a titanium alloy cantilever

calculate the max deflection in a titanium alloy cantilever beam that can support a 100n load at the end of the beam

  Its specific heat ratio is 14 and gas constant is 0287

an open brayton cycle engine operates with a compressor-pressure ratio of 6 an inlet temperature of 20 c and inlet

  Air enters an adiabatic compressor at 20 degc and 100 kpa

air enters an adiabatic compressor at 20 degc and 100 kpa at a rate of 2 kgs and exits at 700 kpa. if the power input

  Combustion heats it to 1500 k in a constant-volume process

air in an internal-combustion engine has 227degc 1000 kpa with a volume of 0.l m3. combustion heats it to 1500 k in a

  What sets of planes diffract the x-rays

Titanium in the BCC structure has a radius of 0.1423 nm.

  Draw a schematic of band structure of a compound that has s

draw a schematic of band structure of a compound that has s and p orbitals occupied. show where is the fermi energy and

  Determine the initial and final temperatures of the helium

the volume of 1.5 kg of helium in a piston-cylinder device is initially 9 m3. now the helium is compressed to 5 m3

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd