Reference no: EM132859809
Assignment - The Ant
OBJECTIVE: This assignment will test your knowledge of the configuration that we have covered so far. You will see configuration of housekeeping, interfaces, STP, and VLANs.
1. HOUSEKEEPING
On each switch, configure housekeeping on each device using the information provided below, and using the device names given.
1.a) Configure SSH using the following information:
- RSA Modulus: 1024
- Domain name: <your last name>.net
*Note: If I was creating a domain name, it would be sardella.net.
1.b) Passwords - Create 3 users in each device
User 1: <your first name>
User 1 Password: password123
User 2: Chris
User 2 Password: cisco123
User 3: Moana
User 3 Password: TheSeaBeckons
Enable Secret: DISNEY
1.c) Set the timeout value for the console line to 15 minutes, and the timeout for the vty lines to 10 minutes. Ensure both prompt you for a username and password.
2. SPANNING TREE
2.a) Ensure that the SnowWhite switch is the root bridge for all VLANs.
2.b) Enable Rapid STP on all switches.
3. INTERFACES
3.a) You will need to create VLAN interfaces on the SnowWhite switch and use them as default gateways for your hosts and servers. I have given you the number of hosts for each VLAN; you are required to subnet accordingly. Assign the first address of each subnet to the VLAN interface that you will create for each VLAN.
Here is an example:
Let's say that VLAN42 needs 42 hosts. In order to accommodate 42 hosts, I would need a subnet with 6 host bits, giving a subnet mask of 255.255.255.192. If I choose to use 10.42.0.0/26 as my subnet, I would configure the following ONLY on the SnowWhite switch:
SnowWhite# configure terminal
SnowWhite(config)# interface vlan 42
SnowWhite(config-if)# ip address 10.42.0.1 255.255.255.192
SnowWhite(config-if)# no shutdown
Then, statically assign the 5th address of the subnet to the host on that subnet.
3.b) Assign the ports on the SnowWhite switch AND the layer 2 switch into the appropriate VLAN, as follows (assuming the SnowWhite switch is connected to the layer 2 switch using fa0/1):
SnowWhite# configure terminal
SnowWhite(config)# vlan 42
SwowWhite(config-vlan)# exit
SnowWhite(config)# interface fa0/1
SnowWhite(config-if)# switchport mode access
SnowWhite(config-if)# switchport access vlan 42
In the case of the Etherchannel configurations between the SnowWhite switch and (for example) the Aurora switch, you will want to ensure that they are configured as a trunk:
SnowWhite# configure terminal
SnowWhite(config)# interface range fa0/23-24
SnowWhite(config-if-range)# channel-group 1 mode active
SnowWhite(config-if-range)# exit
SnowWhite(config)# interface port-channel 1
SnowWhite(config-if)# switchport mode trunk
SnowWhite(config-if)# switchport trunk encapsulation dot1q
*Note: You do not need the #switchport trunk encapsulation dot1q command on the layer 2 switches.
4. SUBMISSION
When complete, submit the following:
4.a) Your completed packet tracer file named Assignment 7 - Your Name.pkt. Do not submit a .pkz file.
4.b) A text file containing the output of the following commands. Note that some of these commands will be longer than a page. Ensure that you get the output of the entire command. Missing information will result in marks deducted.
On SnowWhite
# show vlan brief
# show interface trunk
# show ip interface brief
# show etherchannel summary
# show spanning-tree vlan 22
# show spanning-tree vlan 62
# show spanning-tree vlan 3
# show spanning-tree vlan 7
# show spanning-tree vlan 60
# show spanning-tree vlan 700
# show spanning-tree vlan 27
# show spanning-tree vlan 72
# show crypto key mypubkey rsa
# show running-config
On Cinderella and Aurora
# show vlan brief
# show interface trunk
# show etherchannel summary
# show spanning-tree vlan 22
# show crypto key mypubkey rsa
# show running-config
On Belle and Jasmine
# show vlan brief
# show interface trunk
# show etherchannel summary
# show spanning-tree vlan 60
# show crypto key mypubkey rsa
# show running-config
On Anna
# show vlan brief
# show spanning-tree vlan 72
# show crypto key mypubkey rsa
# show running-config
On Marian
# show vlan brief
# show spanning-tree vlan 27
# show crypto key mypubkey rsa
# show running-config
On Megara
# show vlan brief
# show spanning-tree vlan 700
# show crypto key mypubkey rsa
# show running-config
On Mulan, Tiana, and Rapunzel
# show vlan brief
# show spanning-tree vlan 60
# show crypto key mypubkey rsa
# show running-config
On Kida
# show vlan brief
# show spanning-tree vlan 7
# show crypto key mypubkey rsa
# show running-config
On Anastasia
# show vlan brief
# show spanning-tree vlan 3
# show crypto key mypubkey rsa
# show running-config
On Elsa
# show vlan brief
# show spanning-tree vlan 62
# show crypto key mypubkey rsa
# show running-config
Attachment:- Assignment Ant.rar