Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A three-phase, 60 Hz induction motor run at 1720 RPM and the following losses are known: stator copper loss =50 watts, rotor copper loss = 65 watts, combined rotational loss = 85 watts. Determine the following a) Number of poles (4-pole) b) slip (4.44%) c) Air-gap Power (1,464 watts) d) Output power (1,314 watts) e) Input power (1,514 watts) f) Efficiency (86.8%) g) Output Torque (7.3 N-m) h) Apparent power if the power factor is 0.85 Lag (1,781 VA)
Adding dopants to a sample of silicon is found to reduce the Hall coefficient by a factor of 10 and increase the conductivity by a factor of 5. What effect has this dopant addition had on the mean free path
A positron (same mass as electron) moving at .8c collides head on with a stationary electron producing two photons with EQUAL ANGLES relative to the incoming positron. Find the photon energies, wavelengths and angle
1. The net charge through a cross section of a circuit element is given by q(t)=2t+t^2 C. As usual, t is in seconds. Find the current through the element in amperes. 2. the current through a given circuit element is given by i(t)=2e^-t A. As usual..
A 50 V DC power supply is connected to a 100 Ohm load resistor. The tested current flowing through the resistor is 0.49 A. find the internal resistance of the DC power suppy.
Each single phase transformer has an identical number of turns in the primary and secondary windings. If a line-to-line voltage of 480V is applied on the wye windings, compute the line-to-line voltage on the delta windings.
A collector modulated transmitter has a supply voltage of 48 V and an average collector current of 600 mA. What is the input power to the transmitter. How much modulating signal power is needed to produce 100 percent modulation
Design a first order activehigh pass filter with a high frequency gain of 10 and a cut-offfrequency of 400 Hz. Choose C = 100 nF.Determine Ri and Rf. and Design a Sallen-Key low passfilter with Q = 4 and fo = 5000 Hz.
1. Given R = 50Kohm and C = 100nF what is the frequency of oscillation 2. Given a required frequency of oscillation of f = 10kHz and R = 8kohm, what should the value of C be Calculate the signal to noise ratio given RMS Noise Voltage = 20mV and RMS S..
Use Shannon's expansion theorem to implement the following function using a 2:1 MUX and other non-MUX gates you may need. LetZ be your select bit and manipulate the formula directly (i.e.don't use the graphical trick).
A 10Ω resisitor is connected across a 120-V rms sinusoidal 60-Hz line. What value is the closest to the average current flowing in the resistor between t=0 and t=.0042 sec
1 batman = 3 kilograms 1 hogshead = 63 gallons A basketball has a mass of approximately 624 grams and a volume of 0.25 cubic feet. Determine the density of the basketball in units of arroba per peck.
An analog line concentrator resides logically between the line circuits and the line side of a switching fabric. One might be placed physically at the distribution point in the loop architecture or, even at the pedestal- in which case, the line ci..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd