Annual maintenance to make worthwhile to buy van inststed

Assignment Help Mechanical Engineering
Reference no: EM13713195

A construction manager just starting in private practice needs a van to carry crew and equipment. She can lease a used van for $3,051 per year, paid at the beginning of each year, in which case maintenance is provide. Alternatively, she can buy a used van for $6,259 and pay for maintenance herself. She expects to keep the van for three years at which time she could sell it for $1,233. What is the most she should pay for uniform annual maintenance to make it worthwhile to buy the van instead of leasing it, if her MARR is 20%?

Reference no: EM13713195

Questions Cloud

What will be the approximate temperature of the alloy : Is it possible to have a copper–silver alloy that, at equilibrium, consists of a \beta phase of composition 92 wt% Ag–8 wt% Cu and also a liquid phase of composition 76 wt% Ag–24 wt% Cu? If so, what will be the approximate temperature of the alloy? I..
What additional calculations will you needs : Two large circular coils with N tightly wound turns of radius R yield a uniform magnetic field. If the two coils are separated by a distance R. What additional calculations will you needs to perform to conclude that the field at this location is ind..
Determine the exit area of the nozzle : Air enters a nozzle steadily with a density of 2.5 kg/m3 and velocity of 40 m/s. It leaves the nozzle at a density of 0.81 kg/m3 and an exit velocity of 150 m/s. If the inlet area of the nozzle is 100 cm2, determine the exit area of the nozzle.
What is the annual equivalent cost for the truck : The initial cost of a pickup truck is $10,478 and will have a salvage value of $3,959 after five years. Maintenance is estimated to be a uniform gradient amount of $142 per year, with zero dollar for first year maintenance. The operation cost is esti..
Annual maintenance to make worthwhile to buy van inststed : A construction manager just starting in private practice needs a van to carry crew and equipment. She can lease a used van for $3,051 per year, paid at the beginning of each year, in which case maintenance is provide. Alternatively, she can buy a use..
What is the angle between vector : If the cross product of a vector of length 5 and a vector of length 3 in a vector of length 10. What is the angle between them?
Semi-circular cross-section with radius : A stiletto heel has a semi-circular cross-section with radius of 0.25 in. Due to walking over irregular surfaces and shifts in body weight, moments of up to 30 lb.-in. can act where the heel attaches to the shoe. Determine the maximum tensile or comp..
Rate of heat transfer between the steam and cooling water : A shell-and-tube heat exchanger is used to cool a flow of steam using a stream of cooling water. The steam enters the heat exchanger at 0.1 bar and a quality of 91% (state 1), and exits as a saturated liquid at the same pressure (state 2). The mass f..
Identify parameters : Read (a,b,c); if(a!=0){d=b*b-4*a*c;if(d

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd