Analyze for phases present at 100 degrees above the

Assignment Help Mechanical Engineering
Reference no: EM13611722

A bearing steel with 1.2 wt.% C is analyzed for its microstructure after annealing heat treatment. a) Write down the phase reaction that occurs in this steel at 727oC.

b) What kind of microstructure will be found at room temperature?

c) Analyze for phases present at 100 degrees above the reaction temperature, for their compositions and amounts in the steel.

d) How much pro-reaction phase will be found in the steel? What is its composition?

e) How much of the reaction product mixture is formed? What is its `composition?

f) What are the fractional amounts (relative fractions) of the two phases in the two phase mixture?

g) How much actual amounts of the two phases are present with respect to the alloy in the two phase mixture?

Reference no: EM13611722

Questions Cloud

Rancher roy wants to make a rectangular garden that he will : rancher roy wants to make a rectangular garden that he will plant during november with winter vegetables. the outer
Write out the expected counts under the null hypothesis and : 1. epistasis is the control of a phenotype by two or more interacting genes. in a dominant epistatic model one gene can
George dick an employee of plum corporation drove his car : george dick an employee of plum corporation drove his car atotal of 17.966miles during 2008. of the total miles
A clothing manufacturer has 100 m of silk and 180 m of wool : a clothing manufacturer has 100 m of silk and 180 m of wool. to make a suit requires 2m of silk and 3m of wool and to
Analyze for phases present at 100 degrees above the : a bearing steel with 1.2 wt. c is analyzed for its microstructure after annealing heat treatment. a write down the
Assume that the membrane acts like a parallel plate : the membrane surrounding a living cell consists of an inner and an outer wall that are separated by a small space.
The media often attempts to predict the outcome of national : the media often attempts to predict the outcome of national elections. why are they often wrong? based on the concepts
A piece of wire 22 m long is cut into two pieces one piece : a piece of wire 22 m long is cut into two pieces. one piece is bent into a square and the other is bent into a circle.a
A population of scores with mu 50 and sigma 6 the : describe the major differences between the following two distributions.a. a population of scores with mu 50 and sigma

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the volume of the tank

Determine a) the volume of the tank,b)the final temperature and pressure, and c) the internal energychange of the water.

  Determine the energy change if the system mass

For the process where q= 62.5 kj/kg and wkcs= 60 kj/kg determine the energy change if the system mass is 2 kg.

  Calculate the initial angular acceleration

A dump truck is shown in the figure. The loaded container has a mass of 8000 Kg and may be modelled as a solid homogeneous block. The hydraulic cylinder applies a force of 300 kN to the container in the starting position shown.

  Explain finding exit velocity from air nozzle

Finding exit velocity from air nozzle, Air enters a nozzle operating at steady state at 800 ºR with a negligible velocity and exits the nozzle at 570 ºR.

  A total of 200 mol of a compound is allowed to react in a

a total of 2.00 mol of a compound is allowed to react in a foam coffee cup that contains 138 g of water. the reaction

  Estimate the density of an aluminum-magnesium alloy used

estimate the density of an aluminum-magnesium alloy used for soda cans as a weighted average of the densities of

  Determine the minimum diameter d required

Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded. If the normal stress in each rod must be limited to 110 MPa, determine the minimum diameter D required for each rod.

  What is the compressor steady state response

What is the compressor's steady state response when a 30kg absorber with a stiffness of 1.3*10^5 N/m is added to the end of the beam? Please determine how to change the absorber to minimize the response of the beam.

  If this same system is excited by a harmonic force of

a machine part of mass 1.95 kg vibrates in a viscous medium. determine the damping coefficient when a harmonic exciting

  Calculate the critical load pcr for the following end

a 9-m-long steel e 200 gpa pipe column has an outside diameter of 220 mm and a wall thickness of 8 mm. the column is

  Dtermine the maximum stress and the direction of the

a shaft is subjected to bending and torsion such that the bending stress on the surface is 80 mpa and the shear stress

  Derive an equation for the work of a mechanically

derive an equation for the work of a mechanically reversible isothermal compression of 1 mole of a gas from an initial

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd