An internal combustion engine with clearance volume of 60

Assignment Help Mechanical Engineering
Reference no: EM13633259

An internal combustion engine with clearance volume of 60 cm3 and compression ratio of 8.5 is modeled using the following four processes:

Process 1-2: Polytropic compression with n = 1.2

Process 2-3: Constant volume heat addition

Process 3-4: Polytropic expansion with n = 1.3

Process 4-1: Constant volume heat rejection

Consider air in the cylinder is at 100 kPa and 77 degrees C at the start of compression and that the maximum temperature during the cycle is 1700 K. Consider variable specific heats for air.

(a) Find the pressure (kPa), volume (cm3), and temperature (K) at all states in the cycle.

(b) Calculate thermal efficiency (%) of the cycle.

(c) Show the cycle on P-v diagram. Label states and show property values.

Reference no: EM13633259

Questions Cloud

Determine the power input hp and heat transfer rate btumin : helium gas is compressed reversibly from 16 psia and 85 degree f to 120 psia. the helium enters the compressor with a
Calculate the amount of cano32 x4h2os needed so that the : 1 calculate the masses of cano32 x4h2os and kio3s required tomake 10 g of caio32s. calculate the amount of cano32
When four people with a combined mass of 320 kg sit down in : when four people with a combined mass of 320 kg sit down in a car they find that the car drops 0.50 cm lower on its
A 039-kg object connected to a light spring with a force : a 0.39-kg object connected to a light spring with a force constant of 20.2 nm oscillates on a frictionless horizontal
An internal combustion engine with clearance volume of 60 : an internal combustion engine with clearance volume of 60 cm3 and compression ratio of 8.5 is modeled using the
What was the speed of the car before impact assuming no : an automobile having a mass of 1000 kg is driven into a brick wall in a safety test. the bumper behaves like a spring
Suppose the claimed drying time is true that is 45 : a paint company claims their paint will be completely dry within 45 minutes after application. recently customers have
A what is the potential energy stored in the two bands : a slingshot consists of a light leather cup containing a stone. the cup is pulled back against two parallel rubber
The resulting life data from the batteries had a mean of : a popular flashlight that uses d size batteries was selected and severa of the same models were purchased to test the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd