User Account

All Pages

An industrial water shutoff valve is designed to operate

Assignment Help Mechanical Engineering
Reference no: EM13344817

An Industrial water shutoff valve is designed to operate with 30lbs of force and will encounter 200lbs of resistance force applied to a 1.5in diameter axle. What is the required actual mechanical advantage of the system?

Reference no: EM13344817

Questions Cloud

During an ap the membrane potential typically moves from : during an ap the membrane potential typically moves from -70mv to 20mv and back again. in a cell with 10um radius and
A wheel barrow is used to lift a 200 lb load the length : a wheel barrow is used to lift a 200 lb load. the length from the wheel axle to the center of the load is 2 ft. the
A micrometer caliper is used to measure the diameter of a : a micrometer caliper is used to measure the diameter of a bolt and a reading of 0.768 inches is obtained. based on
Two slender rods of negligible weight are pin-connected at : two slender rods of negligible weight are pin-connected at a and attached to the 18-lb block b and the 80-lb block c as
An industrial water shutoff valve is designed to operate : an industrial water shutoff valve is designed to operate with 30lbs of force and will encounter 200lbs of resistance
The 24m wide portion abcd of an inclined cantilevered : the 2.4m wide portion abcd of an inclined cantilevered walk-way is partially supported by members ef and gh. knowing
A 07-lb block rests on top of a 05-lb block supported by : a 0.7-lb block rests on top of a 0.5-lb block supported by but not attached to a spring of constant 9 lbft. the upper
The 18 kg block starts from rest and moves upward when : the 18 kg block starts from rest and moves upward when constant forces of 20 n and 40 n are applied to supporting
A variable force and appropriate energy transfers are : ten kilograms of water initially at 3000 kpa 200degc are contained in a piston-cylindernbspdevice shown below. a

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Draw a graph of system head and fluid power

Draw a graph of system head and fluid power against flow rate on one sheet of graph paper, using the values determined in(c)

  Find the velocity of the final system

If the bullets stick to the block and they move together find the velocity of the final system and find the total impulse of each bullet if the movement takes 0.5s before coming to a stop.

  Will the engineers decide to use the steel

Assume they test null hypothesis H0: versus H1: Will the engineers decide to use the steel if H0 is rejected? Will the engineers decide to use the steel if H0 is not rejected?

  Calculate the force required to displace the bellow

How to calculate the force required to displace the Bellow for 10mm which is fixed in the pipe line. It is a ring type bellow and i want to find axial force.

  Explain the first law of thermodynamics

Explain the first law of thermodynamics using the conversion of a fuel (gasoline or diesel) in an internal combustion engine. Provide sufficient details (sentences and illustration) to explain the first law.

  The 24m wide portion abcd of an inclined cantilevered

the 2.4m wide portion abcd of an inclined cantilevered walk-way is partially supported by members ef and gh. knowing

  Determine the smallest allowable value of the coefficient

determine the smallest allowable value of the coefficient of static friction between the collar and the rod if the collar is not to slide when a) a =15° b)a = 45°. Indicate for each case the direction of the impending motion.

  Determine the average normal stress in link bd

The link BD is a single solid bar with a width x thickness measuring 1.000 in. x 0.50 in. If the pins at A, B and D have a diameter of 0.375 in, determine the average normal stress in link BD when:(b) Fx = 0 and Fy =4.00 kips.

  Explain finding exit velocity from air nozzle

Finding exit velocity from air nozzle, Air enters a nozzle operating at steady state at 800 ºR with a negligible velocity and exits the nozzle at 570 ºR.

  Is the proposed system sound

let it cool back to the outdoor temperature, pass it through a turbine, and discharge the cold air leaving the turbine into the house. from a thermodynamic point of view, is the proposed system sound?

  Define- hydraulic mean radius

Define- hydraulic mean radius, hydraulic dept, section factor and most efficient dhannel cross section.

  Determine the required velocity

Coal discharged from a dump truck with an initial velocity (v)= 1.8m/s at 50 degrees falls on conveyor belt B. Determine the required velocity v(B) of the belt if the relative velocity with which the coal hits the belt is to be vertical.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd