An exit air bulk average temperature t bo 127 0c is

Assignment Help Mechanical Engineering
Reference no: EM13618541

Air at 1.0 atmosphere pressure and 77 0C enters a 5.0 mm i.d. tube with a bulk average velocity of 2.5 m/s. the velocity profile is developed and the thermal profile is developing. The tube length is 1.0 m, and a constant heat flux is imposed by the tube surface on the air over the entire length. An exit air bulk average temperature, T b,o = 127 0C, is required. Determine the exit h, the uniform heat flux and the exit tube surface temperature.

Reference no: EM13618541

Questions Cloud

The cost of debt for a company is associated with specific : the cost of debt for a company is associated with specific measurable financial obligations. the cost of equity however
A company is studying the number of daily debit card : overproduction of uric acid in the body can be an indication of cell breakdown. this may be an advance indication of
A cell membrane has a resistance and a capacitance and thus : a cell membrane has a resistance and a capacitance and thus a characteristic time constant. what is the time constant
You have 4629802 in a brokerage account and you plan to : you have 46298.02 in a brokerage account and you plan to deposit an additional 5500 at the end of every future year
An exit air bulk average temperature t bo 127 0c is : air at 1.0 atmosphere pressure and 77 0c enters a 5.0 mm i.d. tube with a bulk average velocity of 2.5 ms. the velocity
You have just received notification that you have won the : you have just received notification that you have won the 2.1 million first prize in the centennial lottery. however
Allen air lines must liquidate some equipment that is : allen air lines must liquidate some equipment that is being replaced. the equipment originally cost 12 million of which
What is the ratio dadb of the values for the planets : two spaceships a and b are exploring a new planet. relative to this planet spaceship a has a speed of 0.60c while
B if the speed of the bat is increased is the frequency : a bat moving with speed of 3.25 ms and emitting sound of 35.0 khz approaches a moth at rest on a tree trunk. a what

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the magnitude of the initial velocity

determine the magnitude of the initial velocity of the bullet and the magnitude of the force exerted by the bullet on the block.

  Determine the circumference where the effort is applied

A 7/16 nut driver with a 1 1/2 inch diameter handle is used to install a 1/4 20 UNC bolt into a robotic arm. Determine the circumference where the effort is applied

  A pitot-static tube is used to measure the velocity of 20

a pitot-static tube is used to measure the velocity of 20 degrees c 68f water flowing in an open channel. if a

  Determine the specific volume of superheated water vapor at

determine the specific volume of superheated water vapor at 15mpa and 350oc using a the ideal gas equation b the

  Neglect the small mass and friction of the pulley and

the system is released from rest with the cable taut. neglect the small mass and friction of the pulley and calculate

  Determine the magnitude of its acceleration

If the motorcycle has a deceleration of a_t = -(0.001s);{rm m}/{rm s}^{ 2 } and its speed at position A is 18 m/s, determine the magnitude of its acceleration when it passes point B.

  Kinetic and potential energy effects are negligible for

a piston-cylinder assembly contains 1kg of water initially occupying a volume of 0.5m3 at 1bar. energy transfer by heat

  A pump steadily delivers 152 kgs of water at the conditions

a pump steadily delivers 15.2 kgs of water at the conditions given below. calculate the pump power kw. there is no heat

  After load p is applied joint b moves to the coordinate

the two bars shown in the figure are used to support a load p. when unloaded joint b has coordinates 0 0. after load p

  Landing gear system structural design

Problem Statement Consider the landing gear shown below. Working in teprns of two, come up with a single optimized design for given operational conditions and design considerations

  The system undergoes a polytropic process with pv12 const

a piston cylinder assembly containing h2o initially has a temperature of 130degc and a specific internal energy of 700

  Unidirectional reinforced composites1 calculating the

unidirectional reinforced composites1. calculating the mechanical properties of unidirectionally reinforced composites

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd