An aluminum thin-walled cylinder is 40 mm id inner diameter

Assignment Help Mechanical Engineering
Reference no: EM13628410

An aluminum thin-walled cylinder is 40 mm ID (inner diameter) by 50mm OD (outer diameter) and is subjected to an internal pressure, P. The material has stress allowable of 36x103 psi. Find the maximum allowable, P if a safety factor of 3 is required.

If this cylinder has end cap at the both ends, determine P if a safety factor of 3 is required.

Reference no: EM13628410

Questions Cloud

The purpose of this process is to ensure the defect rate : in a tire factor the quality control inspector examines a randomly chosen sample of 16 tires. when more than one
A 95 confidence interval for the population mean birth : an srs of 18 recent birth records at the local hospital was selected. in the sample the average birth weight was 119.6
If the electrons travel in the lab through a tube 25 km : a what is the speed v of an electron whose kinetic energy is 1.5104 times its rest energy? you can state the difference
How many ways is it possible to observe a sample of n7 : how many ways is it possible to observe a sample of n7 observations from a population of n10 observations in which the
An aluminum thin-walled cylinder is 40 mm id inner diameter : an aluminum thin-walled cylinder is 40 mm id inner diameter by 50mm od outer diameter and is subjected to an internal
A pencil 157 cm long is released from a vertical position : a pencil 15.7 cm long is released from a vertical position with the eraser end resting on a table. the eraser does not
If f1 110n f2 121n and f3 85n determine the magnitude : if f1 110n f2 121n and f3 85n determine the magnitude and coordinate direction angles of the resultant couple
Suppose the amount of a popular sport drink in bottles : suppose the amount of a popular sport drink in bottles leaving the filling machine has approximately a normal
Neglecting the effect of the fillets and of stress : neglecting the effect of the fillets and of stress concentrations determine the smallest permissible diameters of the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Five kilograms of water h2o sealed in a piston-cylinder

five kilograms of water h2o sealed in a piston-cylinder device undergoes 3 quasi-equilibrium processes that complete a

  Determine the final temperature k and the final pressure

a rigid well insulated container is outfitted with a moveable but frictionless partition that separates two sides but

  Find an expression for the torsional constant k in terms of

a thin metal disk of mass m2.00 x 10-3 kg and radius r2.20cm is attached at its center to a long fiber. when the disk

  Find the magnitdue of the acceleration when it reaches

a sled is traveling down a curve which can be approxmiated by a parabola y .01x2. find the magnitdue of the

  The air leaves the coil at 55 f 13 c db 54 f 12 c wb a

air enters a cooling coil at the rate of 5000 cfm 2.4 m3s at 80 f 27 c db 68 f 20 c wb and sea-level pressure. the air

  The automobile shown has 1200kg mass with center of gravity

the automobile shown has 1200kg mass with center of gravity at point g and all wheel have the same 0.34m radius if the

  Prepare a report on thermal analysis

Prepare a report on Thermal analysis - The cooling curve method is one of the oldest and simplest methods to determine phase diagrams and phase transition temperatures

  Same exit pressure of 1 bar produces 90 of the work

a sugar mill in florida has been disposing of bagasse by open-air burning. by using the dried bagasse as boiler fuel in

  What is the proeutectoid phase

Consider 6.0 kg of austenite containing 0.45 wt% C, cooled to below 727 degrees Celcius (1341 degrees Farenheit).

  Determine the turbine work output

Determine (a) the turbine work output, in kJ/kg, and (b) the thermal efficiency of the cycle. Also, show the cycle on a T-s diagram with respect to saturation lines.

  The gate opens when water levels reaches h2m on the left

water gate is hinged at point o. angle between the gate and the ground is given alpha 60 degrees. the gate opens when

  Determine the heat transfer through the rod

A steel rod 1 cm in diameter and 30 cm long protrudes from a steel surface at 150 C. The rod is surrounded by air at 10 C with a convective heat transfer coefficient of 10 W/m2 C. The thermal conductivity of steel is 114 W/m C. Determine the heat ..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd