An airplane is traveling at a constant speed of 200 ms air

Assignment Help Mechanical Engineering
Reference no: EM13627730

An airplane is traveling at a constant speed of 200 m/s. Air enters the jet engine at the rate of 40 kg/s, while the combustion products are discharged at an exit velocity of 600 m/s relative to the airplane. The intake area is 0.3 square meters, and the exit area is 0.6 square meters. The ambient pressure is 0.7 atm, and the pressure at the exit of the engine 0.72 atm. Calculate the thrust developed by the engine. Assume uniform steady conditions at the inlet and exit and the properties of the products of combustion to be the same as those of air.

Reference no: EM13627730

Questions Cloud

A bag contains 12 colored balls each ball being either : a bag contains 12 colored balls each ball being either black or white. the probability of drawing a white ball twice
A ray of light traveling in air strikes the surface of a : a ray of light traveling in air strikes the surface of a certain plastic slab at 63.0 degrees with respect to the
A 500-kg object is hung from the bottom end of a vertical : a 5.00-kg object is hung from the bottom end of a vertical spring fastened to an overhead beam. the object is set into
The corresponding mass flow rates not the original : incoming air flow of 200 m3h at a temperature of 20oc and a humidity ratio of 0.012 kgvkga is mixed in a chamber with
An airplane is traveling at a constant speed of 200 ms air : an airplane is traveling at a constant speed of 200 ms. air enters the jet engine at the rate of 40 kgs while the
Water in a piston-cylinder assembly undergoes two processes : water in a piston-cylinder assembly undergoes two processes in series from an initial state where the pressure is 1.0
A loaded railroad car with mass m is rolling at a constant : a loaded railroad car with mass m is rolling at a constant speed v0 when it couples with a massless bumber system.
A ship leaves port at 100pm and sails in the direction n35w : a ship leaves port at 1.00p.m and sails in the direction n35w degrees at the rate of 20mihr. anothership leaves port at
The l12 of a bearing is the life of the bearing at which 15 : the l12 of a bearing is the life of the bearing at which 15 failures may be expected. a new bearing design follows a

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A round casting is 0 2 m in diameter and 1 m in length what

a round casting is 0. 2 m in diameter and 1 m in length. another casting of the same metal is elliptical in cross

  Using this form for the diagonal nodes and appropriate

the diagonal of a long triangular bar 45-45-90 triangle section is well insulated. while sides of equivalent length are

  A sky diver with a mass of 70 kg jumps from an aircraft the

a sky diver with a mass of 70 kg jumps from an aircraft. the aerodynamic drag force acting on the sky diver is known to

  A city water main to the water tower and is 794 feet above

based solely on static elevation head if the water level in a city water tower is 860 feet above sea level and the

  What is the change in periosteal diameter required

Cortical bone gets weaker with aging, but it turns out that diaphyseal diameters can also change with aging, particularly in males, such that the safety factor of the diaphysis is approximately constant with aging.

  1 name six types of springs 2 name three types of gears 3

answer the following questions1. name six types of springs.2. name three types of gears.3. state hookes law.4. give the

  I the isentropic efficiency of the compressor is 80

refrigerant 134a enters an adiabtic compressor as a saturated vapour at -20degree c and exits at 1mpa pressure. if the

  Samples i want a unique version of this

i want a unique version of this

  Stoichiometrically how many kg of methanol are required for

biodiesel is produced from vegetable or animal oils. usually the glycerine in the oil is replaced by methanol. since

  An outdoor track is 420 ft in diameter a runner increases

an outdoor track is 420 ft in diameter. a runner increases her speed at a constant rate from 14 to 24 fts over a

  Pumps and heat recovery

Energy in the home, personal energy use and home energy efficiency. Efficient use of ‘waste' heat and renewable heat sources.

  Assume that you are responsible for the design of a

assume that you are responsible for the design of a wide-plate tension member built from a structural aluminum. the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd