An actual refrigerator absorbs 500 kj of heat from a sink

Assignment Help Mechanical Engineering
Reference no: EM13631483

An actual refrigerator absorbs 500 kJ of heat from a sink at 250 K and reject 660 kJ of heat to environment at 300 K. T0 = 300 K. the heat transfer processes are reversible. Determine The entropy generation s for the refrigerator, in kJ/K. The irreversibility of the device, in kJ and The exergy deposited in the TL cold space, in kJ.

Reference no: EM13631483

Questions Cloud

Of all college freshmen who try out for the track team the : of all college freshmen who try out for the track team the coach will only accept 30. if 15 freshmen try out for the
What is the temperature gradient in the wall and what is : water at a temperature of t 25oc flows over one of the surfaces of a steel wall aisi 1010 ks 61.7wmk whose temperature
The uniform beam ab in figure 1239 has a mass of 900 ibm g : the uniform beam ab in figure 12.39 has a mass of 900 ibm. g sub l is equal to 32.1740 ftsecsec.a. for a force f of
A 1 microci hot particle was removed from a workers forearm : a 1 microci hot particle was removed from a workers forearm using a tape press. an isotopic analysis of the particle is
An actual refrigerator absorbs 500 kj of heat from a sink : an actual refrigerator absorbs 500 kj of heat from a sink at 250 k and reject 660 kj of heat to environment at 300 k.
Ten kg of water is in a closed rigid container with a : air is compressed from an initial temperature of 20 degc and pressure of 100 kpa to a final pressure of 1000 kpa. the
Provide a 95 confidence interval estimate for the average : a small stock brokerage firm wants to determine the average daily sales in dollars of stocks to their clients.a sample
Show that the rate at which shaft work is obtained or : a. show that the rate at which shaft work is obtained or required for a reversible change of state in a closed system
The mean diameter of a ball bearing produced by a certain : the mean diameter of a ball bearing produced by a certain manufacturer is 0.80 cm with a standard deviation of 0.03 cm.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  An air pressure is to be measured relative to atmosphere

an air pressure is to be measured relative to atmosphere using an inclined manometer with a resolution of 1 mm and a

  The barometer reads 760 cm hg what is the pressure in psia

a pressure gauge reads 23.1 in hg inches of mercury vacuum i.e. -23.1 in hg gauge. the barometer reads 76.0 cm hg. what

  Assuming the engine above is a 37 liter v-6 operating at

assuming the engine above is a 3.7 liter v-6 operating at 7000 rpm determine the followingvtdc and vbdc per

  1 the initial conditions for an air-standard otto cycle

1. the initial conditions for an air-standard otto cycle operating with a compression ratio of 81 are 95 kpa and 17o c.

  A beam with length l 40 in and a rectangular cross section

a beam with length l 40 in and a rectangular cross section with 2 in width and 3 in height is subjected to a uniformly

  What is the largets size mm internal through crack that a

1 the critical crack length for a through crack in a thick plate of 7150-t651 aluminum alloy that is in uniaxial

  The r-410a is compressed to 2mpa 60 c in a reversible

a cylinderpiston contains a saturated vapor r-410a at 10 c the volume is 10 l. the r-410a is compressed to 2mpa 60 c in

  Find the angular velocity of link cd

(a) Find the angular velocity of link CD and the velocity of the pin relative to the slot in link CD. (b) Find the angular acceleration of link CD and the acceleration of the pin relative to the slot in link CD.

  Measure the length of the beam what is the torque

measure the length of the beam. what is the torque calibration coefficient? 7 explain any anomalies - differences from

  The net contents in ounces of canned soup is a random

the net contents in ounces of canned soup is a random varialbe with probability distribution fx 4x-11.75 11.75 lt x lt

  The discharge is located 20 ft 6 m higher than the entrance

500 galmin 30 ls of 100 degree f 40 degree c water flows through 300 ft 90m of 6-inch sch 40 steel pipe. the pipe

  How many engagement points on flywheel would be necessary

A full revolution press has 100 rpm flywheel rotation. The press is equipped with tow hand trip devices mounted on the machine at a distance of 20 inches from the point of operation. How many engagement points on the flywheel would be necessary to ma..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd