An 8 lbm box is moving around the circle of radius ra 2 ft

Assignment Help Mechanical Engineering
Reference no: EM13610451

An 8 lbm box is moving around the circle of radius rA = 2 ft with a speed of vA = 5 ft/s while connected to the end of the rope. Just after (not before) the box passes point A, the rope is pulled with a constant inward speed of 4 ft/s.

a) Calculate the total velocity of the box at the instant it reaches point B.

b) Calculate the amount of work done from A to B assuming friction is negligible.

Reference no: EM13610451

Questions Cloud

Evaluate the work and heat transfer for the process in btu : one pound of nitrogen as an ideal gas expands isothermally at 70degf from a volume of 1 ft3 to a volume of 2 ft3.
Suppose 13 of american adults believe that the highest : suppose 13 of american adults believe that the highest priority of america is to protect freedom of speech. we will
The discharge is located 20 ft 6 m higher than the entrance : 500 galmin 30 ls of 100 degree f 40 degree c water flows through 300 ft 90m of 6-inch sch 40 steel pipe. the pipe
The distribution of the amount of money in savings accounts : the distribution of the amount of money in savings accounts for university of miami students has an average of 1100
An 8 lbm box is moving around the circle of radius ra 2 ft : an 8 lbm box is moving around the circle of radius ra 2 ft with a speed of va 5 fts while connected to the end of the
Heated air at 1 atm and 100 degrees f is to be transported : heated air at 1 atm and 100 degrees f is to be transported in a 400 ft long circular plasitc duct at a rate of 12ft3s.
If the ph level of the reservoir is ok the results at each : a water treatment plant needs to maintain the ph of the water in the reservoir at a certain level. to monitor this they
If np is greater than or equal to 15 and n1-p is greater : if np is greater than or equal to 15 and n1-p is greater than or equal to 15 what is the approximate shape of the
Same exit pressure of 1 bar produces 90 of the work : a sugar mill in florida has been disposing of bagasse by open-air burning. by using the dried bagasse as boiler fuel in

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd