Amount of water vapor condensed

Assignment Help Mechanical Engineering
Reference no: EM13949753

1. Butane (C4H10) burns completely with 150% of theoretical air. If the combustion products are cooled at 1 atm to temperature T, plot the amount of water vapor condensed, in kmol per kmol of fuel, versus ranging from 20 to 608C.

2. Ethylene (C2H4) burns completely with air and the combustion products are cooled to temperatureat 1 atm. The air-fuel ratio on a mass basis is AF.

(a) Determine for AF 5 15 and 5 708F, the percent excess air and the amount of water vapor condensed, in lb per lbmol of fuel.

(b) Plot the amount of water vapor condensed, in lb per lbmol of fuel, versus ranging from 70 to 1008F, for AF 5 15, 20, 25, 30.

Reference no: EM13949753

Questions Cloud

Determine the dew point temperature of the products : 1. Acetylene (C2H2) enters a torch and burns completely with 110% of theoretical air entering at 748F, 1 atm, 50% relative humidity. Obtain the balanced reaction equation, and determine the dew point temperature of the products, in 8F, at 1  atm...
Determine the dew point temperature of the products : A gaseous fuel mixture with a specified molar analysis burns completely with moist air to form gaseous products as shown in Fig. P13.20. Determine the dew point temperature of the products, in 8C.
A letter to the president of staley company : Staley uses a periodic inventory system. The inventories at January 1, 2008, and December 31, 2009, are correct. However, the ending inventory at December 31, 2008, was overstated $5,000.
Calculate the break-even number of units : Calculate the break-even number of units. Calculate the break-even sales revenue. Calculate the margin of safety in units. Calculate the margin of safety in sales dollars.
Amount of water vapor condensed : Determine for AF 5 15 and T 5 708F, the percent excess air and the amount of water vapor condensed, in lb per lbmol of fuel. Plot the amount of water vapor condensed, in lb per lbmol of fuel, versus T ranging from 70 to 1008F, for AF 5 15, 20, 25, 30..
Draw the fdd from the fd given below : A Course is presented in one or more classrooms, on prescribed days and times
Stored in a safe in the treasurer office : Brief Exercise 8-5 Mingenback Company has the following internal control procedures over cash disbursements. Identify the internal control principle that is applicable to each procedure.
Combustion with the theoretical amount of air : A sample of dried Appanoose County coal has a mass analysis of 71.1% carbon, 5.1% hydrogen (H), 9.0% oxygen (O), 1.4% nitrogen (N2), 5.8% sulfur, and the rest noncombustible ash. For complete combustion with the theoretical amount of air, determin..
Interpret the results of the wilks test : Find the mean vector and covariance matrix for each of the three treatments. Does there appear to be differences between the treatments and do you think that the assumption of equal variances is sensible?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd